John, Can you verify that your CM11A is capable of _receiving_ X10 powerline signals with the TM751 plugged directly into the CM11A? If not your CM11A's...
Hello Charles: I did verify, using your procedure, that the CM11a receiving circuit seems to be working fine. Also, there appears to be no 'signal sucking.' I...
There might be some more CM11 european version (220 v, 50 Hz) available at domadoo in France. I just bought one over there. Regards, Eric Lavillonniere ... ...
On Wed, 11 Aug 2010 14:24:57 -0700 (PDT) ... John, The MS14A is defined as an RF sensor and the RFFORWARD/TRANSCEIVE/RFIGNORE tell Heyu what to do with the RF...
This is really weird. I cannot understand the cause of the following.... In my previous post I indicated that I had both MS14 sensors and heyu working as ...
Now this is really weird....I move the MS14A (C1/C2) to yet another room, and motion sensing events are reported as from C1 but light/dark are reported as ...
Did you program the MS14 to detect motion all the time or only when it is dark? The MS14 can be programmed to detect motion when the onboard photocell is in...
Lol...I think I forgot to do the chicken dance! I agree with your rant tho. I programmed it to detect motion all the time. Yes, I know that removing the ...
I checked my instruction sheet for MS14's and there is no way to change the HU that is used by the light detector. It is always set to one unit code above the...
That is correct, there is no way to change the address of the photodetector. That is why I set up the MS14s to be HU C1/C2, C3/C4. That is what makes this so...
... It sounds like there's something different about the two rooms -- such as one has power on a different leg, has a source of interference, or is very weak....
I have a Rain8II which I programmed via the serial cable to shut off automatically if an X10 is not received after 15 minutes....well about half an hour later...
Hi, I've just created a new discussion group, http://tech.groups.yahoo.com/group/heyu_devel/, heyu_devel@yahoogroups.com, where I'm going to initially submit a...
I have these statements in my crontab: # # A3 DINING ROOM LAMP #turn dining room lamp on at 9:15, off at 10:10 (more or less..) 15 21 * * * heyu "rdelay 15;...
Cron sends a email to the user when the program being executed creates output. You can get around it by redirecting output to /dev/null (stderr and stdout). 15...
Hello Everyone, My old openSUSE 10.2 driven computer with real serial ports has finally died and I am looking at a Sheevaplug, Pogoplug or similar type...
... Hi, If you'd like to use heyu on an embedded system, but avoid building it yourself, then your best option is to select a device that is supported by a...
Hi -- Have two Shiva Plugs -- ran heyu using a USB->Serial converter. Works, OK, compile is not hard but you will have to add packages via apt-get (uses ...
I am not familiar with these machines, but, I'd offer another avenue to consider. I use micro ITX and pico ITX boards and systems for several applications. I...
I run heyu on a NAS which I installed from the Optware distribution as Janusz mentioned, but the NAS seems unstable and I would really like the home automation...
... Hi, Running all my not so powerfull embedded devices diskless, I forgot to mention a possibility of compiling heyu natively on a device, perhaps with an...
Janusz, Me too (low power freak, no spinning disks in the house unless really needed). This is the specific set of instructions I followed for using Debian ...
Not being familiar with Ubuntu I can't say for sure how it is set to run cron. Although from doing a quick google you can set the mail to recipient in...
Hello Seth, I bought my sheevaplug (in the uk) together with an SD card with debian installed. I have installed heyu and other applications onto debian and...
Well, THANK YOU everyone, There is certainly some food for thought there, some of you have done it and help seems available. I am hearing that the Sheevaplug...
Seth - Like Peter604800, I have been running a SheevaPlug in a remote location for almost a year. It provides me with temperature and motion data from a condo...
Seth, I have not had any overheating problems with my sheevaplug. I am absolutely delighted with it. I also use it, via heyu, to monitor my energy use (gas and...
thank you, that resolved the problem, and I learned something new. Then again, I should have read the man page more closely. One point of clarification, why...
