I keep getting this error intermittently: "Interface not ready - received 5a" What is causing it, and how can I get it to stop. It is causing some of my cron...
On Sat, 06 Mar 2004 09:07:24 +0000 ... Please describe in detail how you are using heyu2 in your cron job when you get these messages. Regards, Charles...
I am using a cronjob the loooks like this 0-59/5 * * * * root /usr/bin/mrtg2/mrtg /etc/mrtg2/mrtg.cfg ... in the mrtg config I call mrtg-roomtemp "House Temp" ...
On Mon, 08 Mar 2004 20:10:42 +0000 ... What's happening is that heyu2 is waiting for a message (0x55) from the CM11A that it's ready for the next command, but...
I have a question about my TempLinc. I've programmed it to 'Report on change' in the Fahrenheit scale. House code of 'L'. (ie, heyu2 address L1 L1 L1) When I...
My guess is that you have the sensor located too close to the heat source, i.e., directly over a radiator or in the airstream at the outlet of an air duct. ...
I have a cron job that cycles my cameras on the hour. I think that is it. Here is the output from the command you suggested... Version:2.00ALPHA-4 Searching...
That 0x5b is the CM11A reporting that an uploaded macro has been executed, and it looks like it may be interfering with the temperature report signal from the...
Triggers might cause this collision? I could very wasily have a motion sensor triggering an event (Guest announcer, light on, or camera on action, while the...
Yes, the 0x5b message from the CM11A is sent regardless of whether the macro is executed by a timer or a trigger. (The trigger signal itself is not reported...
(For users familiar with heyu 1.xx but unfamiliar with the enhancements made in heyu2, the earlier release notes beginning with those for heyu2 alpha-1 follow...
I'd appreciate hearing from anyone who has tried heyu2 alpha-5 on a PC under SuSE Linux version 9 - whether or not any basic problems were encountered. Thanks...
I'm also getting a seg fault with SuSE9.0 Alpha-5.0 compiled fine, heyu2 erase, followed by heyu2 upload then seg fault. I have to do yard work now. Will look...
Mark, Looking at your results, it appears that you entered 'heyu erase' rather than 'heyu2 erase', and would therefore be getting a segfault with both heyu and...
On Sun, 2004-03-21 at 08:40, Charles Sullivan wrote: Morning Charles, Ah the crucial missing information! I found typing heyu2 a nuisance so I made an alias in...
Thanks for the additions... I forsee some script writing in my near future. <g> # heyu temp_req preset j5 1 2004/03/30 16:26:18 Temperature = 76 : Location J...
I know this isn't the xtend support page but since I'm using your modified version of xtend I figured I might post here. I have the following lines in my...
On Fri, 02 Apr 2004 03:57:49 +0000 ... Where is Xtend finding its configuration file when it's run in /etc/rc.d/rc.local ? I might suggest you take a look at...
... Not sure. Good point, I always login as root so I just use /root/. xtend assuming it was the default config location. I'll look into that. ... Nothing...
On Mon, 05 Apr 2004 04:19:00 +0000 ... Shudder!!! ... heyu2 and its config file and man pages are different from heyu 1.xx so you can switch back and forth...
Hi, OK, so I've installed heyu 1.35 on a Redhat 7.1 box and seem to be able to load a schedual into the CM11 OK. But I haven't been able to figure out a few...
Hello all, How do I 'heyu2 monitor' multiple house codes? Version:2.00ALPHA-4 My x10.conf file has housecode A specified. But I want to set my motion detectors...
On Sat, 17 Apr 2004 07:24:36 -0400 ... The heyu2 monitor displays X10 power line signals for all housecodes, not just the base housecode of the CM11A. Run...
On Sat, 17 Apr 2004 01:58:55 +0000 ... If heyu is working properly, the heyuhelper script will be executed every time any X10 power line function signal is...
Many PC's sold today are not equipped with RS232 serial ports, only USB ports. I decided to see how well heyu2 would work under Linux using a USB-to-Serial...
See: <http://www.x10.com/products/firecracker/index_firecracker.htm#> Pay $5.90 for S&H in USA. They'll probably add you on their mailing list. The X10...
... Everything is working fine.... heyu2 upload... heyu2 info...all fine.. ... I have the TM751. ... Set tm751 to house code B.. set X10 MS14A to house code...
On Sun, 18 Apr 2004 19:52:04 -0400 ... One frequent problem occurs when a transmitter (like the TM751) and a receiver (like the CM11A) are on different phases...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
