I know this isn't the xtend support page but since I'm using your modified version of xtend I figured I might post here. I have the following lines in my...
On Fri, 02 Apr 2004 03:57:49 +0000 ... Where is Xtend finding its configuration file when it's run in /etc/rc.d/rc.local ? I might suggest you take a look at...
... Not sure. Good point, I always login as root so I just use /root/. xtend assuming it was the default config location. I'll look into that. ... Nothing...
On Mon, 05 Apr 2004 04:19:00 +0000 ... Shudder!!! ... heyu2 and its config file and man pages are different from heyu 1.xx so you can switch back and forth...
Hi, OK, so I've installed heyu 1.35 on a Redhat 7.1 box and seem to be able to load a schedual into the CM11 OK. But I haven't been able to figure out a few...
Hello all, How do I 'heyu2 monitor' multiple house codes? Version:2.00ALPHA-4 My x10.conf file has housecode A specified. But I want to set my motion detectors...
On Sat, 17 Apr 2004 07:24:36 -0400 ... The heyu2 monitor displays X10 power line signals for all housecodes, not just the base housecode of the CM11A. Run...
On Sat, 17 Apr 2004 01:58:55 +0000 ... If heyu is working properly, the heyuhelper script will be executed every time any X10 power line function signal is...
Many PC's sold today are not equipped with RS232 serial ports, only USB ports. I decided to see how well heyu2 would work under Linux using a USB-to-Serial...
See: <http://www.x10.com/products/firecracker/index_firecracker.htm#> Pay $5.90 for S&H in USA. They'll probably add you on their mailing list. The X10...
... Everything is working fine.... heyu2 upload... heyu2 info...all fine.. ... I have the TM751. ... Set tm751 to house code B.. set X10 MS14A to house code...
On Sun, 18 Apr 2004 19:52:04 -0400 ... One frequent problem occurs when a transmitter (like the TM751) and a receiver (like the CM11A) are on different phases...
I have installed heyu and it works fine on its own, but when I try to use it with bluelava I get: Status: Error code 256 was returned! and in the apache log I...
Whenever I type 'heyu2 engine' I get a response that says: Only master heyu channel can restart state engine. What does this mean exactly? Should I do...
On Thu, 29 Apr 2004 00:11:56 -0400 ... It sounds like a user running heyu via Apache doesn't have the same write permission in /var/lock as you do when running...
On Fri, 30 Apr 2004 00:42:21 +0000 ... It sounds like there's a mismatch between the heyu2 relay and heyu2 state engine, or at least a screwed up lock file for...
Thanks, that fixed it right up. No more complaints. I did have to futz with the serial port setting in the config file originally and that may have been it....
Hello all, Heyu2 Alpha v2 Alpha 5.2 is great, but I have one problem that I was hoping somebody else had experienced. I have configured a script to run when A1...
On Tue, 01 Jun 2004 19:52:57 +0000 ... One other config directive which controls this is LAUNCH_SOURCE, which defaults to RCVI. I.e., if not otherwise...
On Fri, 04 Jun 2004 12:38:06 +0100 ... Thanks for reporting back your results Matthew. You probably meant: LAUNCH_SOURCE ANYSRC [mini-tutorial mode ON] You...
I've just started using Heyu2 alpha 5.2 on Red Hat Linux 9 and am looking to migrate all my CM12-resident macro definitions from ActiveHome to Heyu2. I have...
On Tue, 15 Jun 2004 08:30:30 +0100 ... Sorry for the delay in responding but I've been out of town all week. The capability for chaining macros in the CM11A...
Hi Charles ... Many thanks for your helpful reply. The above seems to work well for me. As I understand it, there should be no problems chaining macros if a...
On Tue, 22 Jun 2004 22:07:42 +0100 ... Yes, that's correct. The chain ends when the CM11A sees that the next macro in its EEPROM has zero delay (or sees the...
Hi All, Thanks I needed this info as well. It works great. I was wondering how one would schedule the script to run. Let me explain further. I only want the...
On Tue, 29 Jun 2004 17:19:17 +0000 ... There are several different ways of doing this. One way of course is to have the script figure out what action to take...
Whoops - I put too many $'s in that shell expression. The line should read: SCRIPT A1 on rcvi :: (($X10_Enabled & $isOn)) && myscript.sh Regards, Charles...
Thanks Charles for the reply. I am having trouble getting this to work. I am using heyu2 on a redhat 9 system. What other info can provide to help. Again...
Dave, I assume you're using heyu2 alpha-5.2. Please describe exactly what you've done and what's happening or not happening. If you haven't already done so,...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
