I primarily used Advanced and have not had an mark issues. From: hp9100Series@yahoogroups.com [mailto:hp9100Series@yahoogroups.com] On Behalf Of lowopp Sent:...
That's because you guys aren't getting out your magnifying glasses and loupes and looking really close... Which is the only way that you will ever see the...
Erich, You may be right, but it doesn't change the fact that the wheel marks are there. I personnaly think that they'll always be there with glossy and satin...
Hi, I believe I am going to put my 9180 to Ebay. It is my 3rd printer and I am still not happy as I can't solve the colour cast. In order to see if it was my...
Get Spyder 3 Studio and profile your monitor and whatever paper/ink combination you're using. Until you color manage your workflow you're just shooting in the...
I have found in the past that there was a magenta cast because i had omitted to set *both* lightroom *and* my printer driver setups to use Application managed...
You might want to check the Lightroom forum for this issue. It seems to me there was an issue with MacOS and a particular driver. ... __________ Information...
While I've had zero problems printing to Lightroom with the B9180 over the past years, I'm totally sympathetic to your situation. How do the sample prints turn...
... A further possible cause, described here in the past, is corrupted driver settings. However, if that is the problem, the magenta cast will be evident with...
Agreed. In fact the problem with magenta cast that I experienced was triggered by moving from network connection to usb. In setting up the new usb connection...
Thanks for your answers but to clarify any misunderstandings: I did check and recheck every step of the procedure to make sure all was done properly i.e....
Sounds to me like the Epson paper profile is simply better than the HP paper profile. Not all paper profiles are created equal. Some, even from the paper mfrs....
B8850 set to clean heads every 24hours. Then when I turn it on to make a print it goes through the whole cleaning cycle again.. After what seems to be an age...
... ON PC's at least, it's important to disconnect the printer then reboot before removing the driver with the printer still disconnected. Registry cleaning...
... Printing with the HP canned profile using HPA Glossy should eliminate that possibility. And best use a "known good" reference image for testing such as...
... It will, unless you leave it powered on all the time and able to do it's 24hr housekeeping. Which is the only sensible way to use one of these printers. ...
I agree that a standard image can be extremely helpful. I have links to about 10 of them here: http://www.inkjettips.com/chapters/chapter-2/ (look under L2.2) ...
Have you tried replacing the print head(s) and/or ink? This sounds like a print head issue that has been raised on this forum regularly over the years... Good...
What happens if you configure the 9180 driver for AdobeRGB, configure Lr for "printer manages color" and then send AdobeRGB? Tony, magenta cast is present with...
I agree leave you HP printer on all the time and be happy it self cleans. My Canon printer froze up solid after leaving it off for a few weeks. $500 printer...
I agree. Leave the printer on. It does cost money however. The more you print the more you can amortize the cost of auto purge mode. I don't print very...
Bit confussed here to be honest about leaving the printer on. Mine is in standby, ie; plugged in at the mains with the power button off on the front of the...
I read about all of the problems with the printer. I try to follow HP's recommendations to the letter and have had very few problems. I leave the printer...
As far as I'm aware the B9180 does not have a standby mode. Its either ON, with the blue light illuminated, and the LCD showing READY, or OFF, in which case it...
Hi Brian The original post was about the B8850 which does have a standby mode. This is one of the differences. If you switch the 8850 off but leave it plugged...
... <SNIP> The printer is either ON - or it is OFF. HP recommends leaving it on. Some time back I asked a similar question of the people on this Forum. The...
Hi users of the B9180. Many I am sure will curse this beast! I have had reasonable use from mine, so far... Can anybody cast any light on prints having what...
Hi all, I have just joined, having had a B9180 for just over a year now. I had random pizza wheel problems with 'the same paper'. I eventually bit the bullet...
Thanks Paul, that sounds extremely useful. Can you give an idea of how thick the shims you are using are? brian ... [Non-text portions of this message have...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
