... Sounds like the underside of the heads is rubbing the paper and/or excess ink is dropping onto the paper. Have you got correct paper type selected in the...
... reverted back to LR1 and tried printing the same photos that fail to print properly in LR2, they print perfectly. I can recreate this error exactly each...
Hello everyone, I just discoverd this user group and hope someone out there can help me. I purchased a HP 9180 last week with the intent to print some...
... Hi Tony, The answer is yes to the 3 questions. It goes well for 2-3 photos and then the smudge does show up. I shall contact HP this morning. I did not...
... I would look for Russel Brown's video on printing with this printer. You have to have the profiles selected in LR both 1+2 when you slect other than...
... IF the paper is extremely shiny then yes it is possible. But you can still tape on a leading edge in this case so that the sensor reads off the more matte...
I regularily print 8.5 x 44" on my B9180. I load it in the special media tray. It pulls the paper thruough the printer to the back and when ready shows, I...
Sounds like the problem may be the size of paper you are using. Postcard size is fairly small and this printer is optimized for large format. What this means...
Have tried cleaning the foam sponges to the right of the NEDD? I found that mine were soaked with left over ink. I put a cloth on the sponges and when I...
I would make sure that in the Print module you have selected the proper paper profile. The worse thing is to leave it at none. Also set the rendering to...
HP is shipping a new printer. It seems I have to keep the printheads and cartridges from original printer. So, if I have to re-use the printheads, I assume...
I routinely print 12x36" panos on Hawk Mountain roll paper. My first attempts were scuttled by CS and the driver refusing to accept a custom 13x38" paper...
The excuse that it's not HP paper doesn't make sense to me, although I wouldn't rule out that there might be a limitation in the profile you are using. From...
I too think the origin of your problem is the small print size... Try printing the small images on a single larger sheet of paper (Qimage works well for...
Please forgive my ignorance... this is all new to me! I have gone to the Files, downloaded the RR Premium Matte icc... then I went to print from CS2...File,...
what os are you using? in windows xp saw c:\windows\suste,32\s[pp;\drivers\color on the hp support site you can find some specific information under Hp...
if i could type i would be dangerous that should read window\system32\spool\drivers\color sorry ... From: ann clancy <jaclancy1937@...> Subject: Re:...
my b9180 wants me to clean the printheads manually following user guide instructions. these say open cover and press ok until printhead cartridges move left....
Like most places, HP support is for HP stuff only. They are not trained/supposed to/etc support non HP programs (ie CS3) or other equipment/supplies. HP does...
disregard that message, and within a few minutes the unit which contain the printheads should move over to the area in which they can be removed. ann ... ...
Ann, Vicki--Thank you both very much--I'm okay now but my prints aren't so back to re-calibration by eye/as I do not have a device as yet and the prints are...
unfortunately mine stays put and doesnt change the message either.... waited for approx 20mins now florian ... [Non-text portions of this message have been...
Open top. Then press and HOLD the OK button until the printheads move to the left - about 30 seconds on my printer. I know - it feels like forever. Make sure...
If you are using the B9180 - 50 lb is fine. I'm not sure what model of printer you are using. Check the printer specs for the maximum weight/thickness of...
thanks a lot, now i got it. cleaned em but still no good. i think my aftermarket cartridges are not supplying ink properly.... time to throw more money at this...
yes, b9180/50lb RRPremMatte---checked before ordered--the first print was fine--looked exactly right--then the next four color were muddy-- and the last, I...
Christine, if one print was OK, it is probably not the printer. It is more likely settings in the application/driver, etc. If you post the application you...
