That's quite bizarre. Almost certainly its a software/firmware problem as no mechanical/hardware fault is likely to single out the top left corners of separate...
I should have said that I have uninstalled drivers and software repeatedly, checked printheads, recalibrated several times, all to no avail. I had one call to...
One of the things tech support had me try was :disconnect the printer from the computer>unplug the printer without turning it off>hold the on/off button for 50...
I have the same issue with those papers in my printer also. I don't normally print on both sides, and when I do it's because I use the papers to make test on...
Hey all I found this group while doing a search for parts for my newly obtained HP B9180. So what's up group? Is this printer a reliable photo printer? I'm...
if you bought this new, you should get free replacement! if not, I may have these parts for you ... [Non-text portions of this message have been removed]...
I haven't heard of any suppliers other than HP. I assume this was not a new model since they come with a 1 year warranty. BK “It often seems to me that the...
Also if the shipper did it you should take it up with them BK “It often seems to me that the night is much more alive and richly colored than the day." ...
I bought the B9180 from from CALUMET, I was told that it needed the printhead replaced. The printer come in the box as packaged new but both ends of the large...
... With my previous Epsons I used to run paper through twice to print a copyright stamp on the back. I can't do that with the B9180 as it marks the front...
I know this isn't the "fix" you are looking for, and I don't know how to get rid of the roller marks, but one work-around would be to purchase a rubber stamp...
... print in very pale gray ink which had no print-thru. And I could change the content of the stamp very easily, eg copyright year, image ref no. It also...
Why not just print a label and stick it to the back of the print or if you worry about that then to the matting behind the print. The editor of LenWorks says...
... I've done lots of that with darkroom prints for press use, back when photos really existed except as an evanescent heap of pixels. I even had a dedicated...
Most of us have a separate printer for general use. Why not print the back with that one? I wouldn't worry about the labeling not being archival since the...
... I could not get a borderless print at all when I got the printer 8 months ago. after useless haggling with tech support I went to the hp 9180 support page...
I have always understood that the printer won't print borderless at 13X19. It will print borderless at every other size. When you look for Mats for the...
Hmmm ... I have always been able to print borderless 13x19¹s on my 9100 (though Mac OSX). I recently had an issue with another HP printer and HP said that it...
The majority of my prints are on 13 x 19 full borderless. Mostly HP paper but have have also used non HP and been able to do 13 x 19 borderless full bleed So...
Hello to everyone I've been lurking on the group for while now and have found some good information. Now I'm asking for some advice... I wish to print on some...
Hi john, I have practiced a lot of alt-process printing for long years and, as most of alt-photographers, I'have left my wet darkroom for making digital...
hello to the group--I just ran out of magenta (got the depleted message) and had an open partially used magenta that has been stored in a tupperware container...
I am working with the Red River Card samples and tried to print a standard 7X10 card--but the printer cancells the print job stating the paper is too small---I...
Hi Christine, I print on the RR 7x10" cards all the time. Did you go into the printer settings and create a custom paper size of 7x10"? If not, give that a...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
