Does HP / Aglient / HP-Aglient make any decent bench power supplies? I have a homebrew one but it's starting to fail.. would like a more professional power...
I'd like to replace my cheap russian stereo microscope with something more capable. Has anyone here got any recommendations ? I'm fairly happy using a...
for mux bus......Just "qualify" the clock with the ALE signal ?? Alan G3NYK ... From: "J. Forster" <jfor@...> To: <hp_agilent_equipment@yahoogroups.com> ...
I ended up with an extra one of these counters after some recent swapping. This one is fully tested, clean inside and out (10/10 functionally, 8/10 appearance...
Sort of Logic Analyzers for Dummies book ... Does anyone have some suggestions - the manuals do rather assume you know what you want to do and how you use the...
Hi I got a faulty 8590B here. There is no Gurantee / Calibration Seal, but it looks complete. Pics: http://www.speedshare.org/download.php?id=8C30111211 ...
I bought a broken 8590B for a very good Price, and i cant wait till it arrives. :) I hope its complete... The Seller told me there are the following Error...
I have a 85804-60019 board that I am about to disassemble for the parts. Is there any one that needs this to maintain a 85804? It an be had for $15.00 plus...
Hi, I'm trying to find working serial number and option 001 (Complex Signal Generation) code to enable it. Options can be enable if unit is resetted and give...
I have a collection of Wiltron 560 bits and pieces that need homes - Anyone need any Wiltron 560x Scalar Network Analyzer spares? A bit off topic, but since...
I tried searching the past messages, but when I did so I could only display the first ten, attempting to get to the later ones just invited me to send a...
Hi, The N connector is usable to about 11 or 12 Ghz. The precision N can be used to 18GHz. They can be mated without damage. Never connect a 50 ohm N connector...
Hi guys, I've got a 5300B display with a 5308A counter. It was working well until one power on when it failed. As far as I can tell, each part seems to be...
Hi, I'm about to buy a 16500B that's been somewhat kitted out (two 500MHz DSO channels and a 100/500MHz state/timing analyser), apparently a full set of probes...
I installed the three boards from KISS Electronics, and after a little mucking arround setting up the 410C calibrationwise, I have to report that the AC zero...
Can anyone help with a clean scan for this board? It was used in some versions of the 3336B and in the 3325B generators. My version is C, but a D would be...
I am Looking for the Scale window to be used with the HP 8698b AND 8699b Plugin in the HP 8690b Sweep Ocsillator. Any help would be Appreciated. Email me at...
Does anyone know of a source for the last-released firmware EPROMs for the HP 8753D VNA? HP says the last version for those with older CPU boards was 6.14...
I'm looking for a review of the 8595E. I see that some of you have this unit. I have the oportunity to buy one relativel cheap. How does it work on AM/FM...
Subject says it all. I've got a pristine 8565A that works perfectly when driving an oscilloscope hooked up to its X-Y outputs, but the internal CRT is...
I've owned & used Fluke DMMs and Tektronix scopes. I don't know much about the Agilent U1242A DMM. What's the history of these meters? Quality? Usability? ...
Jens,  I think that I would just replace the 6 ROMs with 1 EEPROM. I assume that I would just copy the binary file to a 27C512 without any changes or...
I see some of these advertised as having 100 KHz to 1 GHz coverage and others as covering 800 Mhz to 1 GHz. Is there a way to tell the frequency coverage...
Is there such an animal? My downloaded manual seems to be lacking in a lot of areas! The unit worked for a few hours and then started going squirrely. Random...
My 3314A reports E-19 after power up. I ran front panel tests and U210, a Mostek 8K x 8 masked ROM, is indicated as bad. It's the 3rd 24-pin chip from the...
I am Looking for the Scale window to be used with the HP 8698b AND 8699b Plugin in the HP 8690b Sweep Ocsillator. Any help would be Appreciated. Email me at...
My 8970B manual describes to possibility of using an HP 1332A with Options 101 and 315 as a display device to plot gain and NF vs frequency. Unfortunately,...
Hello Community, would anybody have an electronic copy of the Operating & Service Manual or the Operating Note, resp., for the HP 11570A Accessory Kit? This...
Having problems with message search?
