... That sounds a bit like the Tek 7912HB (sorry about off-topic) I bought. It came from New Mexico. Now the cooling fan is supposed to draw air in from the...
Hi, I want to buy a system boot disk for an HP 1653B scope/logic analyzer. Anyone with access to one of these can create a copy of the system boot disk. It is...
Hi All Many thanks for your help. I have some manuals on their way to me. I am looking out for the software now. Best wishes Mervyn ... From: Bob Groschen...
Hello All, I bought an HP3400A voltmeter on ebay and it doesn't work. Surprise! Surprise! That is just my bad luck. I was going to spend some time repairing...
Replacing an old A6 assembly with the new one (part # 03400-66512) is a standard HP modification and many 3400a's have gone through it. The more modern...
In message <000901c53763$d4a06aa0$1b54d5cb@i4b7f6> ... 1) Open up the PDF and zoom into the part of the diagram you want to print. 2) File -> Print, then...
... Hello Benjamin, you were spot on. I looked more carefully and saw a description on retrofitting the newer chopper board on one of the bama manuals. The...
... print. ... to ... generally ... Hello Phil, thanks for your help there Phil. I managed to get some decent size blown up slices of the circuit diagrams on...
Hi Ive got a HP4195A here that no longer boots up. Last operation we did was trying to copy data to a floppy disk - after which the screen froze and became...
Windex??? Are you Greek??? Watch out if you feel something tightening around YOUR neck :-) Joking aside, you got a nice bargain because you knew what you were...
FYI There are varieties of Windex and Windex-Wanna-Be's that have NO ammonia ( just water and surfactants), which if used with forethought are quite helpful...
Hi all, I´m new at this group... I´m looking for information to repair my HP 54502A power supply... The SMPS has a low and pulsating voltage problem... ...
The subject instrument (without a manual or probe) followed me home from an auction. It "seems" to work, but I feel that the proper probe and some instructions...
Hi Guys, I've got a 8153A Lightwave Multimeter Mainframe with a strange problem. Initially, the unit does not power on, but as soon as you touch any of the...
Good morning Bob, Henry, et al: Had a chance to fully test the SA over the weekend and it looks like everything is working as it should. The manuals helped...
... From: Nick Denman To: hp_agilent_equipment@yahoogroups.com Sent: Sunday, April 10, 2005 3:57 PM Subject: Re: [hp_agilent_equipment] HP 8590A manuals Hi...
Hi -- I'm wondering if someone can tell me what instrument(s) used the 5086-7226 YIG-tuned mixer? Trying to figure out what its specs might be. Was it used in...
John, Both the 8566A and B Go to www.parts.agilent.com look it up and it gives you the new P/N 5086-6226...click on Product list and it lists the 85660A and...
Thanks to a VERY kind member who loaned me a paper manual, I have made some progress with my 8552A (with 8553B RF unit). I had been wondering why pressing the...
Heh, I think it depends on the instrument. I think the older Tek documentation (up until the late 70s or so) is great, but I've had problems with newer...
Hi Guys, I am after service manuals (or just circuits ) for Hp 86235A and Hp 86242D plugins (used in the Hp8620C sweeper) Any help, suggestions greatly...
hi, my HP 3325A showed failed tests 1,2,3 and flashed A-CAL fail, i assume the logic is ok, the LED 2 sec. test works fine and buttons seem to work correctly. ...
