I'm looking for service & cal info or manuals for the following. HP 8640B Opt.323 (not commercial 8640B) AN/USM-323. AN/USM-338 oscilloscope. Any leads would...
I've recently tried to use a pair of old 37203A HP-IB Extenders to extend the distance of several IEEE-488 instruments from the controller. I don't have a ...
If I Recall, The Maximum Cable Length For HP-1B Was 20 Meters. Perhaps Someone Else Knows For Sure. Greyhawk ... From: leedyt@... To:...
110
Mark KAHRS
kahrs@...
Jan 15, 2004 7:35 pm
Well, looking at this here manual, there is a RUN/TEST switch (A1S1). The test switch is A1S2 ( 6 pin DIP sw) . You need to set the COAX/OPT switch (A1s5) TO...
hi guys i am trying to locate a hp part or compatable part out of a hp8558b it is a hp part number 5062-2805 or sugest a online cross reference guide i can...
Just wanted to see if anyone might be interested?? Project Location: AZ Project Name: Test & Debug Engineer - Digital and Analog Desired Start Date: 02/02/2004...
Hi, does anybody have some spare TO-3 Hp 1884-0019 parts? they are SCRs or Triacs used in power supply pre-regulators, RCA was the manufacturer. I need either...
Walter, I looked up your HP part number, 1884-0019, in my copy of the FedLog (Federal Logistics) database. This is one of the first times it hasn't shown ANY...
Just bought an HP-184A scope today at the monthly Livermore Electronics Flea Market. Plus, a Tektronix 7704A mainframe scope....$ 15.00 !Checked it at home.The...
I have a functional 184A with an 1809A and 1825A, and the manuals. They're a bit much to copy outright but if I might be of some help please ask. Fred -- <>< ...
Hello Fred. This is Robert. Thank you for your e-mail. Is there a possibility that you might know where I can locate some of the older tube type Hewlett...
... Robert, it looks like we both got snagged by the 'reply to list' setting. No, I neither have nor know of availability of any of the models you listed. My...
... Hi Fred, OK,how about the HV section ? What has happened, is similar to "blooming" in a TV set. I haven't removed the side panels, yet. Focus,etc, has no...
OK, Richard, I'll see what I can do. I'll need a couple of days to dig these up out of (shudder!) "The Storage". I don't maintain the scope in-cal any more...
... Hi Walter, its a 2N3669. HP 1884-0019: VRRM 200V VDRM 600V IT (RMS) 12.5A ITSM 200A PG 0.5W PGM 40W VT (MIN)200V IGT MAX 40.0m VGT MAX 1.5V VTM MAX 1.8V ...
Hi, I would like very much to transfer to my PC data from my Spectrum Analyzer. Someone told me I need this software to do the job: "E4444A BenchLink Spectrum...
Carlos, I just went to the Agilent website. I was shocked to see that Benchlink for spectrum analyzers appears to sell for $310!!! Agilent did not write this...
I have a HP8656A signal generator. Works fine for FM and AM. However, when using it to test a SSB receiver there is a pronounced "warble" in the tone and it is...
They all do that. The 8656A has a lot of close-in phase noise. Not clean enough for any SSB work that requires an extremely stable reference. -- john KE5FX...
I found similar problems with my 8656A. I replaced all electrolytic caps. I also replaced the osc. I believe it's a FET, try Sphere in B.C. they had some....
Hi All! I have recently acquired an HP 1740A dual-beam oscilloscope - but alas without a User Manual. I would appreciate help in acquiring a manual from this...
David, I have the HP 1740A operator's manual, at: http://www.fullnet.com/u/tomg/manuals.htm It's probably also available on line, somewhere, to download. ...
I recently acquired an HP 3457A. The instrument seems to work, but I get error "9 NOT CAL'D" when switching to ohm and freq functions and on completion of the...
