HI all I have had a data Precision 3600 working fine for some years, but now its now drifting up on shorted input until an 'Err' message is annunciated. I...
Greetings, recently someone was looking for Rack Cabinet Screw Clips, just came across them on the bay, Item number: 7534976248. Says "Works with standard...
does anyone have the pin out for the 8350B db-25 programming connector? i want to build a 08410-60146 source control cable to go between the 8350B and my...
You are probably referring to my earlier request for spring nuts to use on a rack cabinet. These spring nuts fit into a channel and actually have a coil...
Someone was kind enough to send me the pin-out of the 8350B programming connector. Unfortunately it isn't completely obvious what pins go to the 8410[BC] from...
Hi all, I am also in contact via email with a person about the HP1741A scope. I am wondering if anyone can explain the step-by-steps to use presistance and or...
Hello all- I was given a 175A a few weeks ago that is complete and in very nice condition. After the usual visual once-over for obvious problems, I fired it...
My 3586A E3.1 repair: Many thanks to Didier (#1759)for his spot on suggestion as to the fix for the 3.1 error on my 3586A. One difference: My VCXO oscillator ...
John Thanks for the tip, I'll file it away just in case I ever need to do it on my 3586C. I'm still trying to find out if HP published an article in their ...
Joe, I was the guy that posted that info. I suggested that you contact the manual dealers on the web. www.big-list.com has a good list of dealers. This...
1826
Andrea Vavassori
andrea@...
Aug 8, 2005 6:20 pm
... I do not have any experience with this particular scope, however I have some on the transistorized 18x family. The beam finder works by injecting a fixed...
Does anyone know where I can find the instruction and/or service manuals for a 4951B Protocol Analyzer? The unit uses a 6 V NiCad cell (a bit smaller than a...
... There are quite a few good historical links at http://www.hpalumni.org/links.htm , including one that eventually takes you to a comprehensive index of HPJ...
Hi Hank HP Journal below has 3586A/B/C introductory article PL Thomas "A programmable selective level meter (wave analyzer) with synthesized tuning,...
Hi Folks, I have an ancient Counter - an HP-5232A - that I would like to try to get going. 1. Can you help with a service manual, please? [I have the cal...
Thanks to John Byers there's a HP Journal article on the 3586. Does anyone have the issue that they can scan? HP Journal below has 3586A/B/C introductory...
As amazing as it may sound many people do not realize how easy it is to LEGALLY stop paying for their groceries! This is how the one hour television show began...
I have reposted my HP 8165A on ebay (50MHz Signal Source, with logarithmic sweep option). I pulled the auction after a couple of days because of a cockpit...
Hi all, I have two 5345A's that both exhibit problems. I want to trouble shoot by swapping boards, but some boards have different revision numbers on them....
Hi, can anyone help me with a circuit diagram for this power supply (0- 360v, 0-100ma) It sufffered an output short whilst at full voltage. as far as I can...
Hi Jeff, ... I have also two 5345A. Unfortunately, one was seriously damaged during transit (check http://jvgavila.com/hp5345a.htm if you wish to look and read...
Hello Everyone I have an 8753B which has developed a fault, and I'd like to find component level schematics. I have the on-site repair manuals, but I think...
Don't have any experience with Agilent but do with RCA Broadcast. Be sure to mark the boards so you can eventually get them back in their original box. I had...
... Jeff, I have owned and worked on 5345A's since they were first introduced. My recollection is that you should have no problems. I don't ever remember a ...
Hello to all, Anyone ever attempted to add option 002 (RF range to 1024 Mhz.) to an 8640B generator ? It looks like a bunch of parts have to be swapped so it...
The main difference is that you don't get calibrated output levelling with the external doubler, since it has to be connected downstream from the attenuator...
... The option 002 goes before the attenuator, so it is preferable. There was a mod-kit available many years ago, I recall buying several from Test Lab in San...
... I believe that it is conventional wisdom that all HP boards are interchangeable - that is that boards performing the same function in two different verions...
