Hello All I was just given an old HP 3439A Digital Voltmeter to play with. It has the 3443 High Gain/Auto Range plugin. The Nixie tubes light but display...
I don't know if it will make you feel any better but I have a Fairchild Model 7000, 5 1/2 digit Nixie tube DMM and I use it all the time. Works perfect. I...
Ripple is about 1.5v on the 150v supplies and about .5v on the 50v supply. This site: https://www.logsa.army.mil/etms/find_etm.cfm has the calibration...
Jorgen, I have an original manual for the HP 3440A voltmeter, which is the same as the 3449 except for the sample rate, cost U$S 12.00 plus shipping. Let me...
Joe I am interested in the manual if it is a service manual with a schematic. You say it is the same as the 3449 (typo?) Is it the same as the 3439 except for...
Hi, Has anyone got a manual that I can copy, scan or whatever for a HP 1740A? Or point me towards where I can download one? All costs re-imbursed. Regards ...
Hello Robin I have operators book scanned-will You have them uploaded? Best Regards Hardy ... From: Robin Birch To: hp_agilent_equipment@yahoogroups.com Sent:...
I managed to switch off and on my trusty HP 3310A yesterday while it was connected to an audio system (not good practise!) and it now refuses to generate a...
Greetings All, I am a new member of the group and am looking forward to an enjoyable time here. I have a large inventory of HP boat anchors which I want to...
Jack Where are you located? tnx Hank WD5JFR ... From: Jack Crone To: hp_agilent_equipment@yahoogroups.com Sent: Friday, May 14, 2004 12:07 AM Subject:...
... I'm in Klamath Falls, Oregon. That is south-central Oregon, 20 miles from the California border and light-years from any recognized civilzation. Jack...
I'm in Tulsa, OK.. ... From: Jack Crone To: hp_agilent_equipment@yahoogroups.com Sent: Saturday, May 15, 2004 4:30 PM Subject: [hp_agilent_equipment] Re:...
Hello Jack. This is Robert. I have a list of H.P. Oscilliscopes I am looking for. Perhaps you might have a few of them or perhaps you could point me in the...
... From: Robert Middleton To: hp_agilent_equipment@yahoogroups.com Sent: Sunday, May 16, 2004 11:18 AM Subject: Re: [hp_agilent_equipment] Introduction Hello...
Hi all, I'm new to this group, but not so new to vintage HP and other test equipment. I'm sure there are a few familar names here! I have recently found a nice...
Hi Robert, I have two HP scopes. One is a 130C, which I will probably keep, at least for now. The other is a 140A with 1405A and 1420A plug ins. I will sell...
Hello Hank and other people in the HP_agilent group! Crikey, "light-years from any recognized civilzation", where on earth does that put me then? Beyond the...
Hello group (Hello Tom Gootee!!) This is my almost first post... I own a nice 4260A universal bridge, it has an issue with R3, the big rotating resistor behind...
Hello Morris! In the Synthesizer Driver, there is a step recovery comb generator which was driven by the 1MHz Signal. From those comb generator the ouput was...
Jack, I have the military model designation cross-references for most or all of the equipment on your list, which I will email to you. Even better, I have...
Rod, Welcome to the hp_agilent_equipment group! If you happen to know anyone who lives near Norfolk, Virginia, the following gov't auction lot might be of...
Sorry for the re-post. I had the wrong "Subject" line, the first time. ... From: Thomas P. Gootee[SMTP:tomg@...] Sent: Monday, May 17, 2004 10:22 AM...
Hello Jack. Thank you for getting back to me. I could be interested in the 140A and also the 851B. Is there a possibility that you could send some photos of...
Hi Jorgen, Thanks for the reply ... The xtal oven seems to be Ok as the oven temp meter settles in the green region after overshooting a little when first...
Hello again, I have already received a number of replies about my sick 4260A. Thanks to the group for their efforts and to the individuals for trying to obtain...