Hello HP guru's. I bought a HP 8620A sweep generator with the plugin 86222B and the 86250D The 86222B goes from 0.01 to 2.4 GHz and the 86250D from 8 - 12.4 ...
Hi, my 6032 System Power Supply is down (no output) and urgently needs to get it up for testing. Can someone help where can I get a free copy of the 6032 ...
... Hi David: 1N21 is a silicon point contact diode. VRRM: peak rev. voltage: 2.5V VR: reversed bias voltage :2v S band receiver mixer. NR: output noise ratio:...
Hi Group, I have recently aquired the above analyser. I practically rescued this from the skip -the previous owner having no more use for it. No manuals were...
... OK, a standard CRT fault - low emmission write gun. Unfortunately, the CRT is not available from Agilent(HP) although the company in Canada who do HP ...
The display problem looking like a crt problem, to be shure about the other problem try to test the analyzer with much higher frequency (in band 0) i.e 1.5 ...
Hi Geoff & Elie, Many thanks for your replies. I had a thought that the crt might be u/s and you have both confirmed it. Thanks Elie for your info re low gain,...
... 2-01C , ... military VTVM, that ... know if the ... tube in a ... accessories for ... the 410 ( ) ... up to 700 MHz ... high with ... me, or even ... or...
Hi: I'm looking for either a manual and/or change sheets that cover the HP 415E with serial prefix 2709A. The change sheets in my manual 00415-90009 are dated...
Steve, others, I also have an HP8565A. I'm in search of a service manual. The usual places have all come up empty for this model. The display in mine is...
... It's on the Agilent web site: http://cpliterature.product.agilent.com/litweb/pdf/08565-90014.pdf (Op/service manual starts on page 13.) Note to Dave...
Thanks, David! I've made the change. Someone goofed and put the installation note at the front of this PDF -that must have confused the web entry team. I...
... Hi Jos, This might help you, if you haven't already seen it: http://www.qsl.net/ke5fx/tg8566.html Here, KE5FX is using an HP 8566B Spectrum Analyzer and an...
does anyone know how to measure the impedance of long wire antennas using an HP-608A oscillator and a HP410C voltmeter or some other simple methode. David...
Hello Mitch, Sorry, I but I havn't fixed it yet. I've got the manual and schematic, and as I'm not familiar with elaborate scopes ( even those built 30 years...
... The problem is that antenna impedance (indeed impedance in general) is a complex quantity R + jX (or G + jB), so it is very difficult to measure using a...
it is being used for transmitting and receiving on lots of different frequincies, i had found a simple way on this site http://noding.com/la8ak/m1.htm but...
Dave, That's helpful. But it doesn't contain any schematics, just the calibration and alignment sections. Is there another number I should be using to get the...
Were you remembering the "Simple Impedance Measuring Bridge" that is about 1/3 of the way down on this page: http://noding.com/la8ak/a1.htm ... different...
no it was different and was made to measure long wires without a receiver, had a built in oscillator and used a seperate analog vom that would dip, sort of a...
Craig: I have a similar question and I'd love to have a real answer to it. I have an HP 8754A network analyzer that is both scalar and vector, and I have both...
... Well, you could do a calibration using shorts, opens, etc out at the end of the coax (by the antenna), and then read the impedance of the antenna directly....
Chuck: Ok, I have the 8754A books, but I don't have a calibration kit or the manual for it. Let's suppose I do have a calibration kit with std. open and short ...
I have also pondered the feasibily of making antenna measurements with a network analyzer. In fact I know it is done quite often although I don't have a lot of...
... Well, in that case, you can't measure the exact impedance at the antenna. In the ideal case, the coax is going to introduce two things: the first is ...
... Well, measuring diverse impedances *is* what a network analyzer is all about. Calibration is a method of measuring the imperfections in the various parts...
Chuck: The application of measuring an antenna at the end of a 500' feed line is to avoid climbing the tower if the antenna is good. And sometimes, we don't...
Gary, ... The vector measurement is not a good choice for this. Even if you climb up and calibrate at the antenna end of the cable, you would need a similarly...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
