Sorry Jim.... I do have a Bird...(have two).... so I'm always looking for elements for it... However, I should have said so... hi. I did find a good Diawa and...
Oops... did I say Jim... it's terrible when the mind goes...or was it my eyes? I meant "John". So you can call me Bill... hi... Bob and the BEAT goes...
There's a hex dump of the Heathkit GC-1000 code on the HeathkitClocks group in the files section. You can ask on the list about availability of the piggyback ...
Hi Mark, If you are hobbyist and have a limited budget, consider an HP 8924C CDMA test set. This is the 8920B analog radio test set with a CDMA adaptor built...
Hi all, I don't have the signal generator higher than 1040MHz. But, I detached the bulkhead from a good HP 8484A and swap it to the faulty HP 8484A. The...
Mirage amplifier for 220MHz... have manual, need schematic. Can not find. Mods-DK and Mirage have the "manual" w/out schematic. Anyone have or know of anyone...
Looking for info on PEK Labs 118-TR. If anyone has an old manual, catalog or specs please contact off-list. (What I know: PEK was located in Sunnyvale, CA but...
Mike, That's going to be really hard to find IMO. It sounds like it's for testing PMT rise time for nuclear research. If you have access, try someplace like...
Did you put the 'faulty' bulkhead into the 'good' body to see if the 'good' body is not also a 'good' sensor? Perhaps it might be a loose connection that is...
If so how the sensor/power meter combination pass the calibration with the 30 db calibration attenuator? Do'se after zero the power meter show about -70 dbm...
Bob - I suggest that you email the WA1MBA microwave mailing list. http://lists.valinet.com/cgi-bin/mailman/listinfo/microwave 73, John K1AE John Allen - PC...
thanks... the guy I bought it from sent me the diagram out of the blue and I had no idea he had one.... oh wellllllll... :-) . Bob W5UQ and the beat goes...
Hi all, I have a faulty counter. Problem seems to be in input sections, digital seems OK. I also have a partial copy of the manual, but many pages missing. So...
I'm looking for an old copy of the PS300 series manual from Stanford Research. The new release (http://www.thinksrs.com/downloads/PDFs/Manuals/PS300m.pdf)...
First, I Wish all the best for this new year I am looking for the external part (the small one with the disk 0 to -12 db) of the level button (index 4) in this...
That's nuts. The full manual w/ parts list is on line: http://www.thinksrs.com/downloads/PDFs/Manuals/PS300m.pdf You didn't talk to the right person. You need...
Those knobs are extremely hard to find. I had to epoxy the knobs back together on my 8565A S.A. at least until I can locate a parts unit with good knobs. The...
Hi, I don't have the 30db attenuator to work with the HP 436A built-in 0dbm power reference. HP 8484A can only work up to -20dbm. But, I can do the "zeroing"...
... I have the 30dB attenuator, but a 30dB attenuator from Mini-Circuits gives the same results - can't you get a 30dB attenuator locally? I like to keep an...
Scott, I don't own a Heathkit GC-1000, but would love to tune in on this group. Always wanted one of these clocks, but as a kid it was way out of my price...
Hi Joe and all, It was the HP 8657A signal generator. The one I fixed the attenuator and low band output amp problems. My 8657A has +/- 0.5db output accuracy...
Dickson - IMO, i would go no further in the disassembly, as there is a risk of ending up with a dead unit. An 8484A with a known 10 db error is not all...
Hi Joe and all, It was the 8657A, the one I fixed the attenuator and output amp problem. The 8657A output is now within +/- 0.5db for all frequency and...
Hey there all! Hope your first couple days of the year went well. So, to get to it.. I'm looking for some advice. If all you had was these HP instruments,...
Hi,some signal generators are definately needed. Function generator RF signal generator if your doing rf work then a spectrum analyser and in addition for ...
