Dear OM, Just saw your message. In case you don't have a manual for your 317, I do have a professional copy (Navy issue) and a copy of the calibration ...
Hi all: I'm looking for a service manual or schematic for a HP 5210A Frequency Meter (original, photocopy, scan, pdf). I couldn't find anything at BAMA or...
Dear Joe, I got my copy of the 317 manual off of the "bama" sight,... down load for free. It is a good copy. Address is ... bama.sbc.edu I have pretty much...
Hi group, Just wondering if anyone has experience fixing the "non-field repairable" attenuator of this Spectrum Analyzer ? My 8558B attenuator sometimes needs...
Benoit, The problem on most HP Attenuators is mechanical. The o-rings on the rods break over time, this allows vertical movement of the rods and hence bad ...
There's not much to it. I have two of them and one had a sticker with the GPIB commands on the bottom. There is only a handful of commands. I tried to...
Hi group !!, Can anybody help I am looking for the keyboard schematic for the 3336 a/b/c synthesizer / level generator ? Thanks in advance, John Barnes ...
Hi all, Does anybody have a scanned Operation & Service Manual for a HP1740A 100MHz oscilloscope. People keep telling me to look in this "logsa.army" website...
Hello John I have the 3336c,and a pdf file with operator and service books. Will upload free to You-can split the file into smaller ones. Yours Hardy ... From:...
Thanks George, I too have two of them ! the problem I have is that even with the dip switch on the back set the same, one of them wont allow me to set the...
Gentlemen, I have a HP 3406A Broadband Sampling Voltmeter I am repairing. According to the test procedure in the manual , the probe assembly is faulty and...
Howdy All- RE: HP1715A (and family) scope -- rear panel foot/bumper. Anyone have a spare rear panel foot (more like a leg) that bolts to the rear apron on the...
Does anyone know what is safe to clean the old style frequency dials on 331A/3330A type units? I dont want to just try somthing and find it removes the...
Bought a 1980B scope on E-bay. Everything works except for the graticule illumination. Is this integral to the CRT like the flood gun approach used on some...
It Is A Flood Gun (On Mine Anyhow), Perhaps A Missing Voltage Or A Socket Jarred Loose. A Manual May Still Be Available For Free Download At The Teknet...
I have a question regarding the subject power meter. According to all of the information I have, including catalogs and the manual, the instrument is supposed...
Brooke - For example, I can take any of my sensors, which are marked to have a 50 dB range and connect them to a signal generator. I start out with the maximum...
Hi Mike: I asked a friend who's probably one of the world's experts on power measurements and he thinks you 436 is defective. His reply is: "Probably the A2...
Brooke - Thanks for the info. The only problem is all three of my 436s behave the same way. What are the chances of all 3 having the same problem? Is there any...
Mike, Before you go and try and repair the power meter try and do a full re-alignment on it. I have found that if you are not getting good readings at the low...
Dan - Thanks for the suggestion. Do you remember if you did indeed get a full 50 dB dynamic range on your 436As? - Regards - Mike Mike B. Feher, N4FS 89 Arnold...
Mike, I think that your dynamic range is dependent upon the sensor used. So, if your sensor a 8481A it goes from +20 to -30 then there you go. Most sensors...
Dan – Thanks again. Before I say anything else I will try the alignment. It just seems odd that all three of my 436As behave the same way, with all 7 of my ...
Hi There, I have a spare HP cro bezel, the older aluminium round type with 4 screw holes. Good condition, a bit dusty, minor tarnish, inside paint good. I'm...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
