I guess I CAN put it all on Epay but it's so heavy that it probably would cost more to ship than it's worth. Craigs might be better in that someone might be...
See the attached tiff for the J5 signals (14 pin end.) Look at the photos if the following is not clear... I pulled the attenuator on my spare 8566B...
Recently I have seen a rash of 8757A's on ePay that all claim to have the same problem ...no display screen being shown. My unit is doing almost the same...
I have an HP 455A probe T Connector that is of no use to me which I would like to sell. It is used but looks to be in good shape. 50-OHM 1 male N and 1...
Hello, Maybe someone can point me in the right direction to solve a GPIB problem with the 5384A frequency counter. I use Agilent IO Controland an USB-GPIB...
Hi, I've not followed the thread closely, but there might be an option for a VHF/UHF tube recifier in the probe. There is a tube, VR92 and equivalents, which...
My HP 8935's display has seen better days. Does anyone have any info on the EL512.256-SG1 display (Datasheet and/or source to purchase). Also any proven...
Hello all, I've just acquired a 5370B with an unstable start input. When I connect the reference output from the rear panel to the start input and select FREQ,...
Wanted to buy one each mating MRA or MRAC 42 pin/socket connectors. These are the rectangular ones used in backplanes for the modulator plug-in on the HP...
I'm trying to understand the floating ROM code for my 7081 (many thanks to Mickle T. for stating the reverse engineering job and pointing me to the right...
I have the following from my personal test equipment system the following: HP-8620C Sweep Oscillator (No Plug-in) HP-8411a Harmonic Frequency Converter 8743A s...
A while ago I picked up an N4691A HP ecal unit (100Khz to 26.5Ghz) supposedly in good working condition, I was unable to test or use it because of lack of...
Hi, This post is not specific to HP/Agilent, but I reckon the issue could be seen on any test instrument, including HP stuff. Has anyone experienced leakage...
I have had my 8753C about one year now. Recently when first time I needed to use it as RF generator and noticed that the RF source amplifier is broken. Signal...
Objet: HP5340 display problem Hello On my wonderfull (and old) frequencemeter HP5340 the right most digit is showing ZERO all the time, other are OK Before...
Guys I am looking for an (apparently obscure) Users Manual for the 83427A Chromatic Dispersion Test Set . I have found reference to it in the 86037B manual...
I am puzzled by my Manual (-90031) which calls for the hybrid in the stop channel U1 to be a 5088-7061. Mine has in that position a 5088-7062 with the U2...
hi there just got a HP54616B scop on my bench. It has issues. When powerup I get a picture that is only 60% of its normal height and it freezes at a message...
Somewhere on my home PC, I already have a spreadsheet of the 6303 instruction set. I don't recall if it was scanned or xls. I'll check... Orin. ... [Non-text...
I have the following from my personal test equipment system the following: HP-8620C Sweep Oscillator (No Plug-in) HP-8411a Harmonic Frequency Converter 8743A s...
So I finally received my EPROM reader/programmer and pulled the first of two PROMs from my 4262A to read it out. A quick glance showed the power and ground ...
http://www.ebay.com/itm/HP-8412A-Phase-Gain-Indicator-/330415866111?pt=BI_Analyzers&hash=item4cee5200ff 2495 "buy it know" and 36.27 shipping listed at least...
Hi, Having just purchased a 5335A, I'm keen to install an oven oscillator and discipline it using GPS(*). Can someone please confirm that I just need the oven...
I need a schematic diagram for CRT module Agilent 54622A (2090-0384) oscilloscope. Useful would be a measured values of operational module too. Thanks for any...
This is a new HP 11730A cable, part # 8120-8319 for $ 50.00 + shipping ($ 5.25) USPS in US, more if to somewhere else. PayPal is acceptable. Let me know if...
AND HE CONTINUES! (Geoff) HAS ANYONE ELSE RAN INTO THIS PROBLEM WITH HIM?????? I THOUGHT THIS WAS A GREAT GROUP TILL NOW!!! How Insulting! From: "Geoff"...
I am looking for a low cost source for a APC 7 to possibly BNC or N connector for my 8411a, or would it be better to just change the connectors? Also looking...
I recently bought 3 HP 4274A LCR meters as a job lot. All were described as BER (beyond economic repair) & so I was up for a challenge. The first one needed a...
