Hi to all, I've just purchased an used HP-8922M GSM Test Set. It works fine and I'm going to use it for HAM homebrewing. It has a lot of features but I wonder...
I noticed this message and have a scope with an identical problem. Did anyone here ever find a solution? ANy suggestions woudlbe appreciated. Thanks!...
... I was the OP and was able to repair the scope. It turned out to be nothing more than a bad battery. I think that the CMOS data was corrupted, leading to...
Hello HP Community, I am looking for informations about Trace Math in the HP 3589A Spectrum / Network Analyzer. The Product Data Sheet merely mentions some...
My HP3320B has failed : No signal output . Power supply and local frequency reference are working good and I suspect the output amplifier. Any help please ?...
... The group's files area? http://groups.yahoo.com/groups/hp_agilent_equipment/files/ Or you could put it on Putfile.com or one of the other free file...
Thanks for the fast info ... I'm glad that I won't have to use it as a space heater. I'll let you know if that works. Thanks! ... I was the OP and was able to...
Hi, Jim- The holes are 1.75" apart, and there are 4 of them. This is the type that has a 6.5" x .5" x 1/8" tab that fits into the side of the case (I don't...
Hi: I am looking for an HP jumper cable used in a HP 16550A. This is a card that goes in HP 16500A/B/C Analysis System and is a 100-MHz State/500-MHz Timing...
Apparently, an 8341A .1 to 20 GHz sweeper can be used with an 8410. (there is a 25 pin D connector on the back labeled as such) Does anyone have any info or...
Hi all, my HP 8131A failed, and I need one NEC uPC104G. It's an HF transistor array. I googled for it, but only found it from $500 minimum order distributors. ...
Marco, I think you have the wrong part number. I think you need uPA104G I just had a look at the service manual from the agilent site. Alldatasheet.com has the...
I'm pretty good at using a an HP 141T and its plugins to analyze RF specrta. I acquired an HP 3582A good from DC to 25 KHz and want to use it to analyze the...
... From: "wd5jfr" <kolesnik@...> To: <hp_agilent_equipment@yahoogroups.com> Sent: Friday, February 02, 2007 7:25 AM Subject: [hp_agilent_equipment]...
I think you should be able to perform the tests you want. The 1982 HP catalog devotes five pages describing the 3582A. One paragraph states: "Transient...
... John, you are right, I made a typing error. It is, of course, the uPA104G, and I searched the web for it. Widely available, but I have not found it in...
I have a HP87075B multiport test set that I would like to use with a 8714es network analyzer. The analyzer is meant to interface with the "C" model, but...
... My recollection is that the 87075A/B work with the 8412/8414ET analyser (transmission/reflection measurements) not the ES which is an S-parameter analyser....
Hi, Whoever it was needed a chip for the DC503, I have a scrap one and am willing to send you a MC4035P. Just email me off group with a postal address. Cheers...
Hello I do believe that You are looking for a low frequency FFT analyzer.They are very easy to come by if You are willing to use the soundcard in Your pc. ...
Hank I dont know the 3582A but am very familiar with the earlier 3561A-marvellous instrument. Used it for all sorts of things, including transient analysis,...
My 8562A has a SMA input connector instead of the usual type N. Is this because it's an option 26, 26.5 GHz instead of 22? Is there a standard bit of plumbing...
the Agilent p/n for the N type connector is: rf input assy. 1250-2180, maybe its still avelible from Agilent [Non-text portions of this message have been...
John, There is a bulkhead version of N(f) to SMA(f) adaptor for that location; you will compromise the 20+ GHz performance with that substitution. Those...
... Excellent advice. Maybe you can use an SMA to "X" cable that reaches all the way to your load. There are two things to keep in mind. First, all HP gear...
This is from memory, so reader beware.... The 3582A pre-dated the 3561A and did not have as robust of a feature set. It was an early FFT-based spectrum...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
