i dont have code for interfacing mobile and microcontroller............... with my programe i can not interface it other so send me more about it........... ...
Hallo All : I want to Divide information into parts about electronics circuits schematics for alarms, audio, car, computers, design idea, fun circuits,...
Hi there I want to know if they all work and if they are acurate. I found one new for $500 and its a 4 channel. Again I want to know what they are best suited...
Hello all, i tried to generate PWm of 18 kHZ from AVR atmega 16 Controller it is generated but it shows lower and upper frequency seperate. upper is ok but 16...
Hallo All : You looked for the picture about the series of electronics circuits diagram about alarms, audio, car, computers, design idea, fun circuits,...
Use a mormal GSM Mobile and use its F-Bus & M-Bus to interface it to the microcontroller.. Search for the GSM AT Commands supported by the mobile... !!YoGeSh...
for a new project we need 6 inputs -- one more than is available on the status port. so we want to use one pin of the control port for input. all the other...
OK I looked at the data sheet that you have included in your question, , Specifically the totem pole out put, I suggest that you use a 10K resistor between the...
thank you very much for your reply! i tried your suggestion and got no improvement. with or without the 10k pull up (and writing a logic 0 to the port to put...
Hi Erik, this sounds like your port is always trying to pull the signal down.... did you write a xxxx0100 to the control port register to enable bi-directional...
L3sT4Rd
l3sT4Rd@...
Apr 10, 2007 6:20 pm
10229
thanks a lot for the advice. i had not been trying that, because sites like this: http://www.beyondlogic.org/spp/parallel.htm seem to say that bit 5 of the...
Hi, I have a USB-Serial cable that I am trying to get my laptop to recognize. Unfortunately, it came with a CD that has driver files for Prolific...
A. Christy Williams
acwill69@...
Apr 16, 2007 12:46 pm
10231
Because of the new audio architecture of Vista, many DirectSound hardware loses hardware acceleration. I wonder how will this affect the support of sound...
Good morning, does anybody know how one can change the format of the log file so that it will log the same as is printed to the screen. Or how can the log be...
Klaus, I wrote a quick program to reformat a 'Hex' type log file into something a little easier to read .. http://home.hvc.rr.com/n2mci/exe/PLOGFRMT.EXE -Pete...
Hi, Im from india. i ve done up wit the circuit for a/d conversion using adc0832 for interfacing serial port of a computer thro rs 232(used max232 in circuit)....
Hi, I have a GPS with a serial I/O (4800,8,N,1). I have two other devices that need the serial information from the GPS. I am reluctant to just attach the...
... If they are in close proximity, .. just connect TX from the GPS to RX of both devices. Electrically that is no problem. Connecting two TXs to one RX,...
Hi, I've been reading about getting reports on HID devices and i still didnt get a positive result. So i write to the list with the hope of getting some lights...
Nuno Santos
developer@...
Apr 25, 2007 3:00 am
10239
Hi, I've been reading about getting reports on HID devices and i still didnt get a positive result. So i write to the list with the hope of getting some lights...
Nuno Santos
developer@...
Apr 25, 2007 3:03 am
10240
I would like to setup status lights to control via software. I'm a software developer, so the software part I can figure out. I guess I'm looking for a way...
Hi is anyone has a new version of C++ (Borland for example) compiler. I am looking for one in the internet for free but nothing there. Thank you in advance ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
