Hi, I have a problem in mouse interfacing: I want to start up WINDOWS without any mouse, because I will connect it to my computer later, but if I disconnect...
Yaser Tavakol
ytavakol@...
Jan 1, 2002 8:04 am
3990
Hi, I have a problem in mouse interfacing: I want to start up WINDOWS without any mouse, because I will connect it to my computer later(by digital swithes),...
Yaser Tavakol
ytavakol@...
Jan 1, 2002 8:08 am
3991
Retrieving info from RS-232 in VC++ i have a project in vc++ in which i have to write a program in vc++ to send and receive data from a scanner(temperature ...
hi, http://www.codeguru.com/network/serialport.shtml http://www.codeguru.com/network/serial.shtml refer these two sites.... hope this would help.. shiv ...
Thanks Tom and David For answering my "unused parport pins" questions! Daniel ... _________________________________________________________________ Join the...
daniel sheltraw
l5gibson@...
Jan 1, 2002 6:17 pm
3994
i am doing my project on data communication through infra red between two PC's using parallel port and handling data through 89c51 microcontroller. if somebody...
Hi Daniel! It's always a pleasure to correspond with someone sufficiently persistent and "humble before the craft" that real learning can happen. I expect...
Happy New Year to All ! I have located the files you mention in your newsgroup post. Thank you for all your help with my project. It truly is folks like you ...
Retrieving info from RS-232 in VC++ i have a project in vc++ in which i have to write a program in vc++ (frontend also) to send and receive data from a...
Retrieving info from RS-232 in VC++ i have a project in vc++ in which i have to write a program in vc++ (frontend also) to send and receive data from a...
Retrieving info from RS-232 in VC++ i have a project in vc++ in which i have to write a program in vc++ (frontend also) to send and receive data from a...
Retrieving info from RS-232 in VC++ i have a project in vc++ in which i have to write a program in vc++ (frontend also) to send and receive data from a...
Folks, I'm using 'AllowIO' to gain access to some CMOS data. My program, which uses _inp and _outp (to ports 0x71 and 0x70, respectively) seems to work fine. I...
Hi, all: My work requrires me to have multiple OSes on one single machine. I have used a FAT32 partition storing my data, therefore when all W9X/2k but NTFS ...
Jacob_Kwo@...
Jan 2, 2002 10:40 pm
4003
There is some discussion going on on this at www.8052.com Please go there and search. regards K.ganeshan ********************************* From: NUMAG DATA...
hi folks,
I want to study microcontrollers can any body name a vendor in India,
preferable Mumbai who supplies starter kits for uC's particulatly the PIC...
Huzaifa S. Sidhpurwala
huz_52@...
Jan 3, 2002 6:25 am
4005
HI Dont know much abt PIC but u can start off with 89C51 from ATMEL. Its a 8051 with flash ROM. Costs only Rs60 at Lamington Rd. Also, the 89C52 which has 8KB...
HI Check out CS8130 by crystal semiconductor. U will find the datasheet on their website. And if someone knows the cost of this chip please let me know. ...
... If you will consider mail-ordering, there is Leading Edge Technologies in the UK. I ordered their LET PIC Basic Plus, and it came to the USA very quickly....
Vinod thanks for ur help, where can i get a programmer for the 89c51 (perhaps at lamington road) thanks for ur help. Byeeeee ... From: Vinod is here...
Huzaifa S. Sidhpurwala
huz_52@...
Jan 4, 2002 2:49 am
4009
Hi everyone! I just finished Draft 2 of the specification RFC of RATbus, a 6x successor to CANbus. I need programming help on this open-source project. ...
HI A lot of info is available on the net for making yur own 8951 programmer.Oriole electronics at Ghatkopar market 8951 programmers...but they are very...
Can anyone help with information about standard keyboard interface? Satyabrata Das [Non-text portions of this message have been removed]...
S. Das
coretech@...
Jan 5, 2002 9:02 am
4012
Hi I wanted to know if there is some device (ic or something else) that lets you control devices like an ordinary bed side lamp digitally using a high or a low...
Hello Das, I think you'll find this site of interest: http://www.beyondlogic.org/ Bye.... ... From: S. Das <coretech@...> To: Interfacing Discussion Group...
Diego Lemos
jdlemos@...
Jan 5, 2002 11:35 pm
4014
use MAX232 it translates b/w pc and jur lamp voltages ... From: "nam_mohitsood" <nam_mohitsood@...> To: <interfacing@yahoogroups.com> Sent: Saturday,...
Zeeshan Akram
u980100@...
Jan 6, 2002 12:24 am
4015
Hi all. I have some standard RTDs ( Ro ~ 100 ohms). Till now they were connected to some locally made temperature indicators and were working fine. Now I want...
Gaurav Jain
gj7da@...
Jan 6, 2002 7:52 am
4016
... No, more than likely, the RTD forms one "arm" of a wheatstone bridge. The bridge is usually driven on two points, and read on the other two. Connecting one...
Well I guess the only thing missing from the article is the actual article itself. I was able to dwnld the pcb drawing and the software but when I tried to...
Dear Mesgaut, If your speed requirement is within one megabit per sec., and you can manage with RS232 on either end of your system,you can consider using an...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
