I m a college student in indonesia, and right now im doing my final project. its dealing with displacement transduser which i choose lvdt as my transduser ne...
Hi, Make sure you have enable USB on through your BIOS setup. Thanks. Alex ... __________________________________ Do you Yahoo!? Yahoo! SiteBuilder - Free web...
Alex Lee
plug_and_play@...
Feb 1, 2004 11:59 pm
7725
How Web camera can be interfaced via USB port in java ? ... Do you Yahoo!? Yahoo! SiteBuilder - Free web site building tool. Try it! [Non-text portions of this...
I m a college student in indonesia, and right now im doing my final project. its dealing with displacement transduser which i choose lvdt as my transduser ne...
hello All, I need help to solve this problem in C++. I am describing below : can any body help me out with this problem? I need to find out the efficient way...
qayyum chowdhury
qayyum@...
Feb 2, 2004 8:12 am
7728
Hi , In the phone you have to enable IrDA port, that is you have to start IrDA in the phone so that the peer device will able to find your phone. Pls let me...
Jayaprakash Sharavana...
A3810C@...
Feb 3, 2004 8:34 am
7729
hi i was struggling with my project work today and thought of seeing the serial
port output on digital oscilloscope. well i ended up viewing only noise on
the...
I have windows2000 pro and Mantrake Linux on my computer I add it a second hard drive a 120gig with USB connection I like to install Red Had Linux to the...
Hi Gaurav, If you set up the oscilloscope properly, the bits are very clear. Also make sure that you've connected to the right pins on the serial port - i.e....
hello, first u check the ground of the CRO.if it is not set properly,there will be noise.think only grounding is the problem. regs, Ramesh M. ... [Non-text...
I¡¯m a beginner in system programming. Now I want to write a program that can ¡®hook¡¯ the action of writing operation in Mircosoft(R) Windows. Whenever...
... Hi Gaurav, Yes, it is possible to see the transmitted waveshape over an RS232 link. Send the same byte repeatedly from your software. Then monitor the TX...
Hi all, I am using visual basic to write one of my program(using UDP) such that data can be transmitted from PC A to PC B. PC A and PC B is each connected to a...
Frank, I have tried to do the same thing. I could not get it to work, even using the floppy boot disk option. I gave up on the idea, but have since learned...
Hi Does anyone have any information about the IDE interface. I am looking for more than the pin outs of the 40 pin cable or the location of the registers in...
Does anyone know anything about the beyond logic web site as far as how to contact these people or if anyone knows if these programs actually work like stated....
Hi Does anyone have any information about the IDE Bus, I need more than the pin out of the 40 way connector and the BIOS registers. Things like who owns or...
I have Targus PA082 and PA096 parallel port USB emulators. They work great with windows on my Sony Vaio that does not have a parallel port for bi-directional...
Hi, The excitation frequency for the LVDT should be as recommended by the supplier of LVDT. As one should expect, the transformer will have a flat response...
Hi! I try to figure out how to use C++ Builder for 1 month but still I have no idea on how do to an interfacing on rs232. On my project, I suppose to feed for...
All, I'm looking for a recommendation .. here goes. I would like to find a USB device that could be programmtically referenced to accept a short AUDIO file...
connect 5 volt input through a capacitor and resistor then inverter to the rx pin of the rs232 port. Then when the 5 volts drops, a pulse will be interpreted...
Feed the signal to one of modem control signals, e.g. the ring indicator (RI). Levels should be -12 / +12 V for RS232 but 0 / +5 V normally works too. Then...
I use their porttalk to do the I/O communication through parallel port, works fine. rduren46 <rduren46@...> wrote: Does anyone know anything about the...
Bei Jin
hijinbei@...
Feb 7, 2004 4:49 am
7747
Wilson, Can you email me the source code? I can take a look for you. Regards,...
Jonathan Fu
fuj_007@...
Feb 7, 2004 4:55 am
7748
Dear All, I have installed porttalk.sys - seemingly correctly - on my notebook with Windows XP. However, when I execute >allowio.exe audela.exe /a (I need ...
Lech Mankiewicz
lech@...
Feb 9, 2004 8:07 am
7749
... ________________________________________________________________________ Yahoo! India Education Special: Study in the UK now. Go to...
Here's the source code. Hope you can point it out for me. Thanks Wilson ... __________________________________ Do you Yahoo!? Yahoo! Finance: Get your refund...
Hello Everybody, Can anyone tell me where to find tutorials for Embeded C(preferably Keil C51), and sample programs to program 8051 microcontroller in C ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
