neranjana <vneranjana@...> wrote: If you have any idea about seven segment display interfacing using 8051 microcontroller, Pls send me It's Better Visit...
Hello! I'm David Kladek from Hungary. I have implemented your PDIUSBD11 firmware to an electronic with PIC16F877 and PDIUSBD12. During the enumeration process...
Kladek Dávid
kladek@...
Nov 2, 2004 8:03 am
8590
Dear neranjana it is so easy. just use a 20ms intrupt. in the intrupt subroutine put the code of 1st segment at the desired port then set bit the pin which is...
dear fellows I am woking on ecp paralel port host is PC and pheripharial is microcontroler .now when i switch to ecp mode writting 011 to Ecr register and now...
Hello Anyone in our group ever use Istrumentation Amplifier INA110? I made a schematic as drawn in the datasheet, but when I short the input, the output is...
I will write down how to do this here. You can also read about it in Kenneth Ayala's book I use it to display numerals hence I use a bcd seven segment drivers...
hi,in my opinion you must refer to 8051 microcontroller book by scott makenzi there is a good sample, good luck shahram jambucha nilesh <inileshce@...>...
Hi, Does anybody know how to allocate / initialise endpoins in USB device ? Is that space, (sink or source space of endpoint ) is alloted in EEPROM connected...
Hi to all….. 1. Dose any one know any type of sensors that can locate where I'm touching on any type of plates…..i.e. if 3 or 4 of those sensors are placed...
Thanks 4 you. 4 spend ur valueble time 4 me. ... Do you Yahoo!? Check out the new Yahoo! Front Page. www.yahoo.com/a [Non-text portions of this message have...
This is a question in a assingment and I should complete it.I write down it. If you have any idea pls send me. * Describe a mechanism to drive four 7-segment...
Hi all, Thanks to those who responded. I have been away and I am just now sorting through the emails. ... Outgoing mail is certified Virus Free. Checked by...
I am new to this subject(interfacing) So I dont know what is the interrupt how set it pls if you know those send me answers using sim 8051. pls help me. ... Do...
Hello Have a look @ the wonderful site on 8051 http://www.8052.com/tutflow.phtml#Interrupts for knowing everything about 8051 micro controller Regards Shibu ...
visit 8052.com vidusha neranjana <vneranjana@...> wrote: I am new to this subject(interfacing) So I dont know what is the interrupt how set it pls if you...
hi i want to interface a crt controller to my 8051 microcontroller but i cannot find any the only crt controller i know is 8275 abt which i cannot find any...
dear neranjana i think that u should first study some books aboat microcontroller such Scott Macenzi or Mazidi. then try to interface with the devices such as...
im louie sison from philippines. im on my thesis now and i wish to interface my computer via the printer port using visual basic6. help pls. anybdody knows how...
i need help... anybdy can teach me how to interface printer port to interface my comp... thanks __________________________________ Do you Yahoo!? Check out the...
Hello friends.... i got a link on net which gives very very good information regarding all kind of interfacing projects..... check this link... will be helpful...
I am in the process of learning about windows security to develop applications to secure my small office computers. Can you point me in the right directions...
Hi, I am have a project to do serial communications with RS-485. I had experience with RS-232. Can anyone explain to me Multi-Drop in RS-485. Is that available...
Hi Programming RS-485 is similar to RS-232C except for address. Program developed with RS-232C can work if U add the address byte at the beginning. U have not...
Please can any one tell me where can I find an LCD like this one on this link with a serial or parallel interface? I searched for it but I could not find...
does any one know of an online documentation of the monitor sense/i.d. lines for svga monitors? there are 3 pins that can be wired to let graphics cards etc....
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
