Hi Jon You could try defining it as a '877 if you intend to use more than 2k flash, or a '628 if you're using less. Most likely this will get you on the road ...
... This is hard to imagine for a chip company. Which datasheet, for instance? -- Ir. E.E. van Andel, Fine Wire Heat Exchangers, Fiwihex B.V. www.fiwihex.com ...
This is the Jallist bi-weekly info message. JAL is a free language (compiler) for the Microchip 16f84 and Scenix SX microcomputers available from the <A...
jallist@yahoogroups.com
Aug 1, 2004 8:53 pm
15889
1 The very beginning: JAL FAQ version 0.03 June 8, 2004 1 1.1 JAL? PIC? Where do I start? 1 1.2 Where to get JAL? 1 1.3 Which PIC? 2 1.4 What's all this JAL...
jallist@yahoogroups.com
Aug 1, 2004 8:53 pm
15890
Thank you for the tip. I have tried this without success, but this is probably due to my inexperience. The project will compile fine, but the porta I/O did not...
You are on the right way. Cheat the compiler to believe you work with a 16F87x. Then will works. include 16F688 but the 16F688.jal will have pragma target chip...
... longer ... instance? ... Hi Eur, I was about to write '16F630 and 16F688' but I looked a little closer. The pin diagrams are still there, but no longer in...
I am trying to make multiple PWMs out of an '877A using the timer0. So far the timer and ISR are working except I can't seem to increment a variable in the ISR...
... I found this problem too, long time ago. I'we made a copy of the time register in ISR and then use the copy in the main. Then everything works even was a...
JULI 2004 ISSUE HIGHLIGHTS: -Flash Microcontrollers with Higher Density Memory and Power Management in 28, 40 & 44 Pin Packages -Cost Effective Flash...
On Tue, 03 Aug 2004 01:18:06 -0000, "mike_gvillo" <mikegvillo@...> ... Re-enabling the timer 0 interrupt enable and GIE is unnecessary. Clearing the ...
Hi Vasile, ... You have used interrupts for a long time, and you're with me that managing this type of vars in ISR and main at same time are dangerous. But...
... I didn't even think at this ! Just to some weird situations which exist, and which completely dissapears when you try to simulate elswhere than inside the...
On Tue, 3 Aug 2004 11:39:40 +0300 (EEST), Vasile Surducan ... Sure. But count can never be more than 254 now. So if speed = 255, speed is always > count ...
... I'm axiously awaiting Word from the Master, so I can release the board. But his board did not arrive yet. ... $25 with soldered SMD parts, one board per...
Put me on the list for a $25 board when they're ready. Is this "just add PIC" or are there other non SMD parts needed ? (I guess MAX2332 etc... but a parts...
Hi Vasile, ... OK. This strange situations comes daily, not only caused by a not so perfect compiler, but also by a not so perfect code, a not so perfect ...
... Where's the main program code , where you (tried to) used time1 ?? I agree with Javi, there's any reason why it shouldn't work, unless you're violating...
... But under what conditions doesn't it work ? What's the interrupt frequency ? GP1, GP2 are shadowed ports, are they used in the main program too ? Stef...
... Thanks Hans, Also note that JALEdit will use any libraries present in your working folder before it uses libraries in the LIB folder. So if using a LCD for...
... Eur, I have a question please. I'm just working to a board having 1206 805 and probably 603 series. As I see, the whole SMD Eagle library have a problem,...
Hi folks, After strugling with some libraries in the past, I'm getting more and more ambitious about/with Jal ;-) My current project (which initially started...
Hello, Now I have someone working with ASM code and the MPLab IDE and I am working with JAL. We would like to work together. My friend wants to stick with the...
In the past two days, I've had several bounced emails come into my mail box with virus attachments. My best guess is that someone out there in "email land" has...
On Wed, 4 Aug 2004 09:59:00 +0300 (EEST), Vasile Surducan ... You mean the white print that says "C18" and "33K"? Some manufacturers (Olimex) clean up the silk...
