Hi, I'm new to the group but not to the Joe cell. The introduction document to thes group states i should read Alex's book again. Is Alex's book still required...
Several years ago I wrapped a five gallon plastic bucket with the 40 layers of al and meat wrapping paper. I then stuffed a roll of fiber glass insulation in...
Smokey, thanks again mate!! I got them! what an amazing thing! I love its simplicity too. Had a thought - if you were to humidify the air before it is going...
Smokey, one question - which of the two methods for controlling air speed through the accumulator do you suggest? the fiberglass wool stuffed in there, as page...
sorry to catch this thread in the middle, maybe this is out of the scope of what you are aiming at, but have you seen the EFIE device from eagle research? or...
So this 40 layer Orgone accumulator doesn't connect to the ground or to battery negative or positive right? And the entire box isnt wraped, only 4 sides right?...
If it there is the possibility that the air is somehow charged by the accumulator, the humidity you want could potentially nullify the affect you are seeking....
Bill, I was able to energize and prep water with a crystal device to the point that it would quickly go to stage 3. However the first time I tried it I used a...
thanks smokey, I had this book on my list of reading. To charge water he was using copper foil I think. I am going to try and get one of these together soon,...
I think Kozyrev used polythylene film. I think that is transparent tape, possibly polycarbonate or polypropylene plastic would work. but then again im just...
... scope of what you are aiming at, but have you seen the EFIE device from eagle research? or the MAF enhancer? ... Simple way to bypass a single 02 sensor: ...
the box that my friend built that worked he had fiberglass and a baffle top and bottom of box with a 1 inch spacing from the top and the bottom of the box and...
Bill have you run across these plans yet i am going to build this box since my friends box has vanished after his death - which i know works but would like to...
Kevin, Group, That is correct by reading the information provided. The top and bottom baffle (fiberglass model) need many holes (250 to 300 x 1/16" holes in...
I am considering buying a EFIE to lean out the air/fuel mixture. Has anyone had problems with damaging valves, burning holes in pistons or other heat issues? ...
Watching your gauges carefully, including the EFIE "dummy lights" should keep you in the clear. Engine temp is a big issue here since the fuel actually assists...
One of the problems I had with my orgone accumulator was watching very closely not to get any shorting in wrapping the layers. 40 layers is a lot of wrapping...
Am I correct in assuming that your end caps were the remaining 2 side of the 6 cube sides of the 40 layer wrap? IE wrap the first 4 sides of the box in a...
This hasn't fully been verified as being compatible with vqlve timing, however if you want a 90 degree timing advance or retard, i believe if you swap the...
Yes. Thank you. My question is: how do you use these devices safely without harming your valves or pistons? Can I get both: lean air/fuel ratio and not...
Is there an optimum air/fuel ratio that will give you good fuel economy (not the absolute best) but not overheat my valves or burn holes in my pistons? I am...
Smokey, Thanks for posting the files. I did find on the google about half of the book. I have couple of questions: -what is inside the accumulator? -what kind...
We currently have several aftermarket engine computer (ECU) options (the LINK is the most popular) available that allow us to set virtually ... any huge gain...
If put the Joe's Cell on a OBDII car won't i need a EFIE or a MAF? I thought the computer would make the fuel richer because of the more efficient burn and...
Philippe, Group, Yes - I used what they call the 'tread' pattern as I felt it gave better thickness than the flat foil. Paper I used was Greaseproof. Both from...
