interesting read here involving charged capacitors and magnetic field self generating power this would b y a healthy cell generates a magnetic field and self...
hi daniel with the ea's u can lower the amount of fuel injected a few ways 1 make the ecu think water temp is hotter than it is 2 make ecu think air temp is...
Actually, it's necessary to do the O2 sensor, no matter what else you change, because it'll override any of the other changes, including the smaller injectors....
BTW, this all presumes that the ECU is operating in closed loop. It's possible to force it into open loop, which I think in most cases causes a very rich...
One additional thought! It's possible to reduce the fuel pressure by running the fuel pump with a pulse width modulator. This would be a lot simpler and most...
... Hi Daniel, fords and many other fuel injection systems used this double pulsing set-up. You are correct. It isn't as efficient as sequential injection...
Hi Bernie. "Condense very slightly"?? The injector sprays into still air, onto the back of the inlet valve, where it stays for a long time, the first charge...
Bernie, after many many hours of trying all sorts of ways to get around the ECU there is only one that will make the kind of difference that is needed. The...
Daniel, You're responding to someone else's email. Tell me specificly what you want the circuit to do. It would be relatively straight forward to divide the...
Hi Bernie. The open loop is the limp home mode, is that right? I have had the engine running in this mode a fair bit, and reducing the flow with a tap to the...
Hi Bernie. Yes, sorry about that, I did respond to someone else there. Never heard of a flip flop. That sounds like they work as they sound. In which case,...
Daniel, Open loop is used when the engine is cold, until the O2 sensors warm up. It's also used when an error is detected. To accomplish what you want, is...
Hi Bernie. Don't worry about it, I'll find some other way. There is no cam angle sensor on these engines. Nor a flywheel sensor. All injector timing is done...
Daniel, You're still missing my point. If each intake port has three injector pulses for each ignition pulse, than if you reduce this to just one pulse you...
Hi Bernie. I thought I had put forth my reasoning on this, and expkained how I intend to supplement any loss of power that may arise from actually only...
Daniel, Maybe the easiest way to accomplish what you want would be to convert to a TBI type system. Just move one or 2 injectors up to the point where the ...
Also, it's probably OK to hook both signals to a single injector so that you get a pulse whenever an intake valve is open, so only moving one injector is ...
Hi All. Well, it seems that Robert Hull has shown his true colors. Turns out that he WILL help get people's cars up and running on the "Hull effect";.... for a...
Hi Daniel: Can you blame Robert? He has given us access to something that may prove to be worth a fortune... and asks for consulting fees from anyone who...
Guys, when I first started the process of making a Joe Cell I found I had to rely on machine shops. I have found these to be uniformly problematic, mainly...
Guys, this post will make little sense to most of you, but I do not apologise for that. The reason is that the fundamental plea of this post is that you should...
Daniel, Actually your post came through about 3 times! Bernie ... From: "krazy4gone" <no_reply@yahoogroups.com> To: <joecellfreeenergydevice@yahoogroups.com> ...
Hey Danial.Been in the backround but monitering the conversations and progress of joecell groups 1-2 ,and the hull effect.I could have missed something but,...
Hello Daniel, Â Â Â I can tell you that I have not paid Robert money. Nathan is the guy who discovered what the switch can do. Robert is the one who spent...
Awesome tip Adrian! Iv'e been on the THE group for a while, but have no intention of dropping the JC. It is too versatile....and beautiful too. KP ... ...
Daniel, I am not on the Oil Cell group and I have not seen the posts you are talking about, but I think we have to be reasonable. Assisting other people takes...
Hello Adrian, This sounds interesting, I had no idea that such cheap cutting machines existed, but are the results really as good as those achieved with a...
Hi, Let me explain the basis of my post. After I had bought my uncut tube for the Joe Cell I found I had an excess of unsuitable (too magnetic) material and so...
... Adrian, I must apologize to all the members for this intrusion upon this forum. I never imagined that Daniel would become so vicious. You did give warnings...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
