If Reel Trading is to high try these people at www.tstar.net/~thunder/trs.html they specialize in k-3 upgrades and will prevent jamming and scratched film...
DAVISD111
davisd111@...
Jul 1, 2000 3:42 pm
1197
... A NOTE FROM REEL TRADING Just to let you know -- this is the same guy that lifted the copyrighted product photos off our site and took our copy nearly word...
John N. DuQuette
jdq@...
Jul 1, 2000 6:09 pm
1198
Hello guys, I was reading the manual from NCS, and I got a little problem understanding where the batteries for the light meter go, and what kind of batteries...
germanlib@...
Jul 1, 2000 11:45 pm
1199
... It goes underneath...in the thing that unscrews. The K-3 was designed to use a mercury cell, now unavailable in the US. I hear you can still get them in...
NCS
da@...
Jul 2, 2000 2:57 am
1200
Hello all, I just purchased my first film camera, a Krasnogorsk-3. I have previously only worked with video and have absoloutely NO EXPERIENCE with film...
Jon Brennan
jonb1@...
Jul 3, 2000 8:46 pm
1201
Hello all, I just purchased my first film camera, a Krasnogorsk-3. I have previously only worked with video and have absoloutely NO EXPERIENCE with film...
Jon Brennan
jonb1@...
Jul 3, 2000 8:49 pm
1202
Please, all people on this list SAVE THIS EMAIL. It has the unsubscribe info. Do not lose it. If you send a general message to the list asking to unsubscribe,...
Mike Friese
Mike@...
Jul 4, 2000 12:09 am
1203
NCS
da@...
Jul 4, 2000 1:10 am
1204
Hi,guys. I just shot my fourth film with the K3 and they all have come back jumpy. The picture isn't steady it's moving up and down rapidly as if I were...
derick_t@...
Jul 4, 2000 3:24 am
1205
In a message dated 7/4/00 3:25:48 AM, derick_t@... writes: << May be I am not loading it right. ... Most likely. ... The little arm in the gate seem to...
PeterH5322@...
Jul 4, 2000 4:24 am
1206
... Just to clarify, the setscrew doesn't control *directly* the tension of the little plunger, it just holds it in position. I assume that if you suspect not...
NCS
da@...
Jul 4, 2000 9:36 pm
1207
In a message dated 7/4/00 1:42:11 PM, da@... writes: << Just to clarify, the setscrew doesn't control *directly* the tension of the little plunger, it...
PeterH5322@...
Jul 4, 2000 10:59 pm
1208
Specific instructions for removing the K-3 front added to the website. http://www.intervalometers.com/k3camera/front.stm Feedback welcome! It was a 15 minute...
NCS
da@...
Jul 4, 2000 11:30 pm
1209
In a message dated 7/4/00 3:30:39 PM, da@... writes: << http://www.intervalometers.com/k3camera/front.stm Feedback welcome! ... I use a dull X-Acto...
PeterH5322@...
Jul 5, 2000 12:11 am
1210
In a message dated 7/4/00 3:30:39 PM, da@... writes: << http://www.intervalometers.com/k3camera/front.stm Feedback welcome! ... The procedure is...
PeterH5322@...
Jul 5, 2000 8:10 am
1211
Can the mirror shutter be cleaned if so how. Does it make a difference in the viewfinder....
DAVISD111
davisd111@...
Jul 5, 2000 8:22 am
1212
I apologize if this question has been asked before. To assist you in understanding my question, I attached a picture (copied from NCS's manual). I put a red...
Eric Johnson
edjohn@...
Jul 5, 2000 11:19 pm
1213
I read through the recent posts on the film gate tension, but wasn't sure if my question was applicable to that answer. I just got the camera, so I haven't...
Eric Johnson
edjohn@...
Jul 5, 2000 11:24 pm
1214
In a message dated 7/5/00 3:21:15 PM, edjohn@... writes: << To assist you in understanding my question, I attached a picture (copied from NCS's...
PeterH5322@...
Jul 5, 2000 11:43 pm
1215
In a message dated 7/5/00 3:25:31 PM, edjohn@... writes: << However, I noticed that the film gate can slide up (in relation to holding the camera as...
PeterH5322@...
Jul 5, 2000 11:50 pm
1216
Hello again everybody, I dont have the money for the Reel Trading upgrade just quite yet, but I'd still like to make sure my camera is in good working...
Jon Brennan
jonb1@...
Jul 6, 2000 12:28 am
1217
NCS
da@...
Jul 6, 2000 12:35 am
1218
... The best thing you can do is load up a dummy load and run it through the camera. If you can, use about 10-15 feet of unexposed negative, run it through,...
Paul Niccolls
frosh15@...
Jul 6, 2000 1:09 am
1219
Dear Peter, Before I do any damage to my new camera, I want to make sure I understand everything completely. This "bridge" has 2 tabs on it. The *'s are the...
Eric Johnson
edjohn@...
Jul 6, 2000 1:29 am
1220
In a message dated 7/5/00 5:41:53 PM, edjohn@... writes: << Before I do any damage to my new camera, I want to make sure I understand everything...
PeterH5322@...
Jul 6, 2000 1:54 am
1221
Would anyone here mind answering some very amateur sound questions? I'm very confused about the process of getting sound transferred onto film. Hypothetical: ...
Eric Johnson
edjohn@...
Jul 8, 2000 1:36 am
1222
... It will be fun to read the answers to this question. I hope its taken seriously and a couple of concise responses for this fellow with a crisp informative...
Michael G. Kramer
yisuhin@...
Jul 8, 2000 2:53 am
1223
... Ill put this in if I may. While your 16mm film will typically be projected in a machine which needs an optical sound track on your film (a wiggly line down...
Michael G. Kramer
yisuhin@...
Jul 8, 2000 3:24 am
1224
... The basics? Resolve your minidisc onto mag film (fullcoat). Now you have a length of 16mm magnetic film that is (if you've timed it correctly) the same...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
