Im currently using fc6 - i compiled and installed the libk8000 files including the mod_k8000 - that kernel module loads fine,.. but on further research i...
Hey everyone i need your help, Im stuck trying to get this k8000 to work with fc6, iv read that recompiling the kernel is the way to go but im assured by the...
Mike, If you've installed libk8000, you should be able to use your k8000 without loading any kernel modules. You only need to load these when you intend to...
Hi all, Now I'm looking for KEL, anyone know what happened. I was using it and it worked amazing well for my uses. I expected it to grow but gone it is. Does...
Hi.. The spam filter of my provider orange.nl has tagged good mail from the k8000 yahoo group as spam. Has any of you also this problem ? I notified orange.nl,...
Hi Hihihi, No, for me (scarlet.be) is working fine. I have however the option to choose the various steps for spam removal: - mailing/big group lists - 100%...
ok then it might be the gender changer on the cable or dare i say it, my buddies PC isn't configuired correctly, which is possible, and of course no printer...
Anyone got any tips for the next step in testing,.. The board is all soldered up fine etc,.. and when i connect the +5 or GND to the test pins, i forget which,...
the maual is on the site too. ... From: Michael Biggs To: k8000@yahoogroups.com Sent: Saturday, May 12, 2007 3:01 PM Subject: [k8000] testing and setup Anyone...
LOL, I just read this mail, and I can not believe someone wrote that whole thing. As a matter of fact, I cant even believe someone wrote that pdf. What's wrong...
Hi.. I received a request from a few scientists from Georgia State University to do a survey in this yahoo group. As far i can see it is a real survey, not...
This yahoo group has been randomly selected (along with more than 40 other yahoo groups) by researchers at Georgia State University to receive an invitation to...
I don't buy it. This is so spam... Karel hihihi <hihihi@...> wrote: Hi.. I received a request from a few scientists from Georgia State University to do ...
Hi everyone, You are welcome to participate in the research or not to participate. But the Virginia Tech research study IS a research project on people's...
hi all I need information about CMM that came before CMMI URGENTLY please ... Best Regards, ... No need to miss a message. Get email on-the-go with Yahoo! Mail...
I have an XP professional with SP2 PC. My 8000 card is assembled and tested. I can set/reset the I/O's with the sample test program running on the XP PC. DA...
I just built a k8005 and am going to control it with my irobot create. does anybody know what bits I need to send it to control the motor. Thank you, Adam...
Hi Adam, The K8005 is controlled electrically by I2C. You could generate these I2C signals with an external I2C IC, or with e.g. a K8000 board. This last...
... Adam - just remember you can't use the Velleman K8005 cards with the K8000 / K8001 combination, just the K8000 on its own. The velleman.be site has...
I am going to control the card with my module that is on my irobot create that I have figured out. What i don't know is what data I need to send to the card...
... You need know how the I2C protocol works. There are explanations on the internet. Then you have to figure out if you hardware can handle the I2C signal. ...
Thanks for all off the info. My robot does support I2C protocol. The robot is actually very open for interfacing with other item. Your info was just what I...
Hey, Here at the lab we needed to control a Velleman K8000-kit with matlab on windows XP. I noticed that there were some questions about this in this message...
hello their, I'm struggling to get my K8000 working under FreeBSD. So I understood their were people who have been able to get the interface working. Is it...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
