Issue: if you want to use a K8000 card sometimes as slave and sometimes as a master, you have to remove the slave parts according to velleman. This is of...
Richard Schaper
richard@...
Jun 5, 2002 2:14 pm
583
Issue: if you want to use a K8000 card sometimes as slave and sometimes as a master, you have to remove the slave parts according to velleman. This is of...
Vanderhaegen Bart
bart.vanderhaegen@...
Jun 5, 2002 10:42 pm
584
... No I didn't know what it was, velleman never metioned it ;-( Do you guese or know what the DIS is? ... ...
Richard Schaper
richard@...
Jun 6, 2002 10:42 am
585
... I think they use it for their K8001 module. if that card is in "run mode" , the K8000 doesn't accept any commands from the computer anymore. I suppose the...
Vanderhaegen Bart
bart.vanderhaegen@...
Jun 6, 2002 12:01 pm
586
has anyone ever made a software routine to detect the k8000 interface card? Or even better, a software tool to check out all the I²C devices on the bus. (and...
Vanderhaegen Bart
bart.vanderhaegen@...
Jun 6, 2002 12:12 pm
587
Hello, Question, does anyone know if the card is reliable for many years ? (example; checking inputs every 0.5 secs) I want to control my house with this, but...
witte_leu
Kristofb@...
Jun 6, 2002 6:14 pm
588
my card has been online since the 1 february 1996, to control my heatingsystem in my house, it works verry verry nice. The cable from the pc to the k8000 is 25...
Ove G.Mikkelsen
heating@...
Jun 6, 2002 8:51 pm
589
... From: Vanderhaegen Bart ... Check de lmsensor library for Linux it has a basic detection program for i2c system bus. It shouldn't be too hard to convert...
tnx for the reply, but a don't understand the language on your site,and the international page is the same language ... How many "card-reads" do you have /sec...
witte_leu
Kristofb@...
Jun 14, 2002 11:36 am
591
... heatingsystem in my house, it works verry verry nice. The cable from the pc to the k8000 is 25 meter long. its 4*2*0.6 pts cable . ... ...
witte_leu
Kristofb@...
Jun 14, 2002 11:37 am
592
maybe you could use the memory module (K8001) for the K8000 so u don't need a PC to run your programs. I haven't one myself but with your cable problem it...
Hi, For the house automation system a friend and I have put together, we are using 4 k8000 cards that are scanned every 20ms. The whole setup is running for...
Hi, A while ago I had a question about torque and Jukka gave me the answer below. After that I was calculating the amount of torque and revolution count I...
Did you use full and half steps? Full steps turns the steppermotor twice faster. ... From: "Marc Horst" <marc.horst@...> To: <k8000@yahoogroups.com> Sent:...
Andreas de Wilt
adewilt@...
Jul 2, 2002 7:08 pm
597
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the k8000 group. File :...
k8000@yahoogroups.com
Jul 3, 2002 8:39 am
598
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the k8000 group. File :...
k8000@yahoogroups.com
Jul 3, 2002 8:41 am
599
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the k8000 group. File :...
k8000@yahoogroups.com
Jul 3, 2002 9:04 am
600
What is the differnce between the K8000 and the K8000RS IO boards?...
sschau80128
uahcs@...
Jul 3, 2002 2:57 pm
601
Hi Let's assume that you have two motors. The ST28 and NEMA23-type motors. You have the ST28 with gearbox and NEMA23 without. You have certain maximum speed...
Jukka Piepponen
jukka.piepponen@...
Jul 4, 2002 6:37 am
602
As in the subject. The thing wouldn't listen to his master. Did i blow the optocoupler ? or is something else playing a nasty trick on me. Help would be...
pe5ed
ed@...
Jul 5, 2002 4:11 pm
603
... "listen to his master" is a bit of a mysterie to me.. It sounds like you have more then one K8000 connected to each other. An other one being the master...
Hi, Did you use full and half steps? Full steps turns the steppermotor twice faster. This is with full steps. I did some other checks: when my application...
... computer to ... (and ... wrong let ... socket. ... I indeed just build it. There is just one of them, so master/slave is not in order. The led 19 is lit...
pe5ed
ed@...
Jul 7, 2002 10:11 am
607
... As in 'I am the master ' Sorry for the confusion, just realised later that i was merely using a metafhor, where that might have been technical information...
pe5ed
ed@...
Jul 7, 2002 10:14 am
608
... I got a boring answer for you :-) Check all the IC and other components to see if everything is really correctly placed. And then check all the solder...
... really ... and ... place ... @ There is nothing boring to that, though the checkup might be. ... Hmm, that is a nifty one Holiday is on tomorrow for ~2...
pe5ed
ed@...
Jul 7, 2002 9:16 pm
611
Hi.. I am not sure, but better safe then sorry.. Looks like there might be something wrong with the email you got from k8000@yahoogroups.com with the subject :...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
