No response :-( no matter - maybe it's not interesting, but I've made it. It was definitely no problem, just a 4 liner ;-) Greetings Guido...
Guido Bening
bening@...
Oct 2, 2002 7:45 am
863
Hi everyone this message is to thank everyone who has added information to this group. It has been very helpful for me since I just bought myself a K8000 kit...
pietbaccaert
pietbaccaert@...
Oct 2, 2002 12:39 pm
864
Ok problem solved :) I got a new LPT card, with other chipset ... This card also uses C800 for I/O but now I can set the dataport to 51200 (C800 HEX = 51200...
Hi The best source of compatible cogwheels, belts and so on are the famous old dot matrix printers (inkjet and lasers too of course). They are very cheep(or...
Jukka Piepponen
jukka.piepponen@...
Oct 2, 2002 6:10 pm
866
Hi Piet, The place I found my wheels (and I'm also living in Belgium) is in a model shop (where they sell small cars and trains). You have to be a little lucky...
At my company we always order from Bergmann aandrijftechniek, they might be expensive for an amateur builder....but if you are looking for those specific...
i am having trouble accesing my crd with delphi , when i start the made program the lights flikker (so ther is data send) , but i cant controll the port's , i...
Has anyone an example of how to make an amplifier ??? Got a thermocouple which gives an output range between 0 and +50 mV DC. I would like to amplifie it to 5...
Has anyone an example of how to make an amplifier ??? Got a thermocouple which gives an output range between 0 and +50 mV DC. I would like to amplifie it to 5...
I'm a beginner and I'd like to check my brand new K8000 card. I have just plugged it on LPT1 and switch it on. So what ? How can I see any result ? Hope you...
bigbosslhg
bigbosslhg@...
Oct 10, 2002 2:39 pm
872
Hi, Use the Test program that comes with the card. I guess it's quite easy if you're not using Win2000 (and XP?), as I do. Otherwise download the testprogram...
... Isn't there a test prog on the floppy that came with the k8000 ? Try it :-) And have a look at the examples in the booklets on how to connect something to...
i didn't install the XP-specific drivers from velleman but i used the driverlinx on Bart's site instead http://users.pandora.be/bartv/winplc/get/driver.exe is...
Hej I have made my k8000 to control the outside light i my house. It's made in VB6 with the new Velleman K2000 driver. My problem is that, when i activate the...
Ulrich Haversen
UH@...
Oct 14, 2002 6:01 am
877
I think you use the K8D.DLL from velleman. With this dll your processor is used up to 90 % for reading a card, and it work really slow. Use the Driverlinx...
... this is a very good solution , got it running in a matter of minutes , and its fast "thanks ronny" (wat did you do with the hair?) , by the way do you no...
Could somebody help me in connect K8000 to input digitals ? I 've configured 8 OUT and 8 IN in my k8000. Ouputs seem to work fine (i've a relay card) but I...
... the i/o inputs are protected with a opto coupler , this means there is a light conection between the card en your input divice , the spec's say that you ...
A OK !!!! I'm not so stupid (I Think). ... the open collector is only for the output! the input is only a led see below. ... Oke first of all its very easy. ...
R. Schaper
richard.schaper@...
Oct 16, 2002 8:21 pm
885
... (220volt) ... MUST I CONNECT DIRECTLY MY POWER SUPPLY OR BATTERY WITH K8000 DIGITAL INPUT OR MUST I PUT A RESISTOR TO REDUCE THE INPUT TO K8000 TO 20-40 ...
... YES!!! but actualy your are using an resistor, its only inside the K8000 its resistor R50 (the big one 470ohm 1watt!!!) look in the manual H8000P-ED1 (the...
Richard Schaper
richard@...
Oct 17, 2002 11:05 am
888
... This 30 volt is wrong. Should be 20 volt for input. The 30 volt is for output usage. <about using it as input> ... I have just measured it. 20 volt gives...
This email is intended to make greetings to joep meloen Richard Schaper hihihik8000 that helped me to ynderstand better k8000 schematics I've tried digital...
Hi, I'm a newbie who just bought a K8000 kit. I don't succeed to communicate from a XP platform with the K8000 though. first of all, the passive tests on the...
Hi What setting do you have in motherboard bios for the printer port ? You should have the printer port at 378 but you wrote that you get both leds light up...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
