Krinnicam is a very interesting program. I downloaded the program(s) a few days ago and the program connects with my Coolpix 5700. I will investigate the...
Hello to all, I'm just joined to this group and I hope to bring my personal effort to this community. I'm using a E5000 camera and other funny toys. Cla. ... ...
I have a Coolpix 5400 that I'd like to get working with krinnicam as a test bed for wide area set up for photogrammetry application. My set up requires that I...
Hi Nick What mode do you have the USB use set on the camera ? It should be set for Mass Storage not PTP. After changing the mode I switched the camera off and...
Setup: Coolpix 995, UC-E1, Win2000. The camera LCD comes on at startup of krinnicam, but shuts off after the first picture is taken and won't come back on. The...
I was build an remote shutter based on Atmel's ATtiny2313 microcontroller. But my Coolpix 4500 does not take a photo until fresh camera launch. Open flash if...
This is very strange (krinnicam doesn't send "set lcd off" commands in the middle of a shot sequence.) Besides, you're using the same setup as I am. Can you...
Sorry for the long delay. There are issues about krinnicam on XP. I'm trying to get these solved for the next version which I'm working on (sorry, only from...
Sorry for the long delay. As far as I know, the MC-EU1 protocol doesn't support downloads (this protocol is tailored to the MC-EU1 remoter shutter controller...
Sorry for the very long delay! Answers below... ... Thank you! ... Sorry but no, it isn't. I'm "fighting" to get some spare time for this project, and...
Sorry for the long delay. Thank you for your interest in the program. I'm trying to get back at this project and I'll be happy if you want to contribute with...
Hi Fred, thank you for your suggestion. I figure that those resistor values depend on the voltage that the computer is driving on DTR. The values I published...
Sorry for the long delay. I've been a bit "out" of lastest Nikon models, but I think that these new cameras (S-series, P-series, etc.) are unlikely to work...
Sorry for the long delay! Answers below... ... SP2. ... Absolutely. I'm working on that for the next version. ... This is a known issue from CP4300 and later...
First of all, sorry for the very, very long delay, and thank you veru much for your feedback. You bring good news, as I wouldn't expect this model to work...
Hi, I haven't experienced that problem, but my camera is a CP995, I haven't tested a CP4500. Can you post a more detailed sequence of the commands you're...
You do realize that these things have already been in production for about 7 years already? DigiSnap 2000 series controllers at www.harbortronics.com If you...
Thank you. I must admit I'm puzzled since I don't see anything wrong in the log file. Can you try the lastest version (v1.06, Files Section)? This one uses a...
... Well, I Was send commands as follow: send 0x00 until answer 0x15 send 0x1B,0x53,0x06,0x00,0x00,0x11,0x02,0x00,0x00,0x00,0x13,0x00 answer 0x06 send...
Comments follow... ... No problem with this part. Just have a look on what the code does if 0xFF packets are received (typically you will receive two of them ...
Not quite. When the button is pressed in the remote, it sends the 2 commands to open the shutter. At 19200bps, the time required is about 5ms, this time serves...
... Your assembly ... My remote shutter sometimes shot until first press, sometimes until second one. I start to think about this like "feature" or "known...
... My goal is to create an utility that enables me multiple exposure with different shutter speeds or max +-EV brackets. If I understood Digisnap is dedicated...
... That's consistent with my results. As the camera is in bulb mode, and the MC-EU1 protocol emulates shutter button press & release, I actually wouldn't...
... I was try to add 2 second delay between full an half press. And, with focus set to infinity, gives not much better results. ... How long exposure times are...
... with focus ... Bad news. I tried several 8 seconds exposures using krinnicam with the serial cable and MC-EU1 mode, focus at infinity, obtaining consistent...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
