Check that you have enabled writes to the I/O area in MCFG2 register. Jiri....
21890
shubham
shubhamearly
Jun 8, 2012 2:56 pm
Hi Jiri Thanks but did you mean the Memory Config Register MCFG1[IOEn field @ bit 19] rather than the MCFG2 because I could not find I/O related stuff in MCFG2...
21891
Markus Kreidl
zapa_marcos
Jun 8, 2012 4:33 pm
Awesome, I was not that far away. ;) best regards & thx Markus...
21892
santiagoozafrain
santiagoozaf...
Jun 8, 2012 8:18 pm
Thanks Sebastian, I've found the solution. Bye, Santiago....
21893
Jiri Gaisler
jiri_gaisler
Jun 8, 2012 8:42 pm
... Yes, I meant mcfg1 of course ... :-) Jiri....
21894
markus
zapa_marcos
Jun 9, 2012 4:42 am
Hi Jan, I still have a problem, Got manufacturer ID 0xa0 and Device ID 0x2373 No device match for READ ID instruction, trying RES instruction.. I browsed the...
21895
Jan Andersson
jan_at_gaisler
Jun 10, 2012 1:27 pm
Hi, The GRMON driver does not support the flash device you are using (it is missing an entry for the manufacturer/device to match against its internal lists of...
21896
Aqeel
aqeel.shah84
Jun 11, 2012 6:23 am
Hi, I am facing a problem with leon3 memory. When i run the system test in simulation, it runs fine. But when i try to run it using tsim, there is an error...
21897
Arvid Bjorkengren
abjorkengren
Jun 11, 2012 7:38 am
Hi, Yes, I have fixed a bug that I believe was the cause. The fix will be included in the next release. /Arvid ... -- Arvid Björkengren Software Design...
21898
ARSLAN
arslan_usman...
Jun 11, 2012 12:52 pm
Hi, I am trying to run the simple GPIO program on ml605 fpga using the leon3 processor. When i run the gpio.exe file it gives IU in error mode (tt = 0x2b) 3 or...
21899
yhoo_mark
Jun 11, 2012 2:29 pm
Hi, I am trying to adapt iu3.vhd in such a way, that it can execute a multiplication from a 32x32 multiplier in one cycle. The frequency might need to be...
21900
Arvid Björkengren
abjorkengren
Jun 11, 2012 2:50 pm
Hi, tt = 0x2b means "data store error". Do an 'inst' command in grmon and try to figure out what caused the error. You need to post your source code if you...
21901
robbiewilliams85
robbiewillia...
Jun 11, 2012 4:18 pm
Hi, does Snapgear 2.6.21 run on board Nexys 2 with LEON 3?...
21902
ARSLAN
arslan_usman...
Jun 12, 2012 2:17 am
Hi, I have uploaded the source code in Files with "Arslan_ tt=0x2b " as folder name kindly have a look at them as well. I tried the 'inst' command when then...
21903
Jiri Gaisler
jiri_gaisler
Jun 12, 2012 7:47 am
You need to enable writes to I/O area in the MCFG1 register of the memory controller. Jiri....
21904
ARSLAN USMAN
arslan_usman...
Jun 12, 2012 9:50 am
How can i enable that? If i write 'mcfg1' in grmon it gives mcfg1 = 0x0003c1ff Does it means it is enabled? ... From: Jiri Gaisler <jiri@...> Subject:...
21905
Arvid Björkengren
abjorkengren...
Jun 12, 2012 10:18 am
You can find the register description on grip.pdf (http://www.gaisler.com/products/grlib/grip.pdf). IOEN is bit 19 of mcfg 1, so make a 'mcfg1 0x000bc1ff' in...
21906
wesleygoncalves88
wesleygoncal...
Jun 12, 2012 3:31 pm
Hi all, I'm working in a board XUPV5-LX110T, with the design leon-xilinx-ml509 and the peripheral SVGA controller is enable. Through grmon I'm trying to...
21907
Greg Dunn
gfdunn2
Jun 12, 2012 5:34 pm
We are developing a board with a UT699 ASIC and are having a problem getting RTEMS to locate the plug and play cores. Specifically, it halts after failing to...
21908
wesleygoncalves88
wesleygoncal...
Jun 12, 2012 8:55 pm
Hi again, I found the problem. First, I had to do "i2c 1 dvi init_ml50x_dvi";. Also, I was using a monitor with VGA cable and a DVI adaptor. This doesn't work....
21909
hyuken87
Jun 12, 2012 11:34 pm
There is no Spartan 6 folder in the FPU netlist archive. Does this mean that we cannot use the FPU on the SP605 design?...
21910
Aqeel
aqeel.shah84
Jun 13, 2012 1:46 am
Hi, I am trying to run the default system test of leon3-asic in tsim. When i run the system.exe file the tsim give an error tsim> run Memory exception at...
21911
ARSLAN USMAN
arslan_usman...
Jun 13, 2012 2:05 am
Hi, I changed the mcfg register in grmon to the value "0x000bc1ff"as you suggested. But still the IU error mode (tt = 0x2b) is there. Thanks [Non-text portions...
21913
Jiri Gaisler
jiri_gaisler
Jun 13, 2012 6:25 am
You cannot run systest on TSIM or real hardware, this has been said many times. Systest relies on an external test module which is only present in the VHDL ...
21914
Jiri Gaisler
jiri_gaisler
Jun 13, 2012 6:33 am
Spartan6 targets will use virtex5 netlists. Jiri....
21915
Aqeel Ahmad
aqeel.shah84
Jun 13, 2012 7:01 am
Ok thanks for that input, one last thing and that will relieve me a lot. If I write my own code for some peripheral, tsim still doesnt work with that (like i...
21916
Jiri Gaisler
jiri_gaisler
Jun 14, 2012 4:51 pm
If you have a license for TSIM professional, you can add modules that emulate your custom peripherals. This is not possible when you use the eval/academic ...
21917
Sebastian E. Garcia
sg_listas
Jun 15, 2012 4:03 am
I'm again over this issue. It turns out that I'm having a problem with the apbuart resources configuration in the application source file. I've verified that...
21918
Aqeel Ahmad
aqeel.shah84
Jun 15, 2012 7:39 am
Ok thanks! Syed Aqeel Ahmad ________________________________ From: Jiri Gaisler <jiri@...> To: leon_sparc@yahoogroups.com Cc: Aqeel Ahmad...
21919
Hilman_Mauludin
hilmatrix
Jun 16, 2012 5:03 am
Hello, I have modified grlib LEON 3 source for DE2-115 to work with 2 ethernet port. I used the driver from example folder for Gaisler Ethernet. My goal is...
