Hi all !!! Could you please tell me differences between GRSIM and TSIM?? Which one do you recommend?? The easiest to install, the easiest to use, the one with...
Hi, if address is 0xefffebe8 when you reach do_mmap2() then the c-library might do something nasty. If you use uclibc check the code that is executed there. ...
By 2.6.11 sparc32-smp support was broken. The Sparc people are working to re-add smp to sparc32, look at http://www.ultralinux.org/lists.html on the status of...
Hi a very successful year to all of you I integrated the OC CAN into my Leon3 Altera-FPGA design and some basic tests are running fine but to really develop...
The core is compatible with the Philips SJA1000, ses this page for details and a data sheet: http://www-eu3.semiconductors.com/pip/SJA1000.html Please report...
thanx Jiri I run it successfully up to 2.000kbit/s with short wires as soon as I´m finished I send it to you by the way: 1. could you please change your...
Hello, I am a beginner in LEON2 and I am studying the cache module in LEON2. However, I have difficulties to understand details of interface between cache and...
Dear Jiri, I am arranging the power information of ARM/MIPS/Leon2, but I can not find out the information of Leon2 power consumption in mW/MHz. Do you have any...
Can you send us the log from Quartus regarding the GRETH warnings? We have run it on both Cyclone-II and Stratix FPGAs and never seen any problems. /Marko...
Power figures are always difficult since they depend heavily on system configuration and cell/ram libraries. The leon core itself (processor + caches) will...
Hi, Do you use an operating system on your board ? Do you know if y free driver for linux exists ? Regards, Francis ... Von: leon_sparc@yahoogroups.com...
Ielsch Francis
francis.ielsch@...
Jan 4, 2006 4:07 pm
7925
There is support for the CAN core in uClinux (our version of snapgear). Select the can4linux driver .. Jiri....
I´m more in the education, training, consulting business and use Leon3 beside the NiosII I come from the Multiprocessor world Transputers, C4x, C6x, Sharc ......
Hi Konrad and Jiri, The mmap() system call do not work under Snapgear-P18 (I test it under GRMON at least). It calls _syscall1() to pass 6 parameters using...
Hi, I run LEON3 on a ALTERA EP1C20F780C7 board using the default Leon configuration for that board and code a program that run in LEON3. When i download my...
you must have a mistake when you compile your software. make sure on the compiler and parameter that you use -- _______________________________________________...
Hi Nabil, I'm going to try to simulate with TSIM. Do you know if I need to buy the HASP key?? Thank you in advance. Ana- ... GRSIM support multiprocessor...
Hello, I'm new to LEON and am trying to get Hello World to run. The board is a Xilinx Virtex-II. I'm using RTEMS-4.6.5. and did a clean install following...
Hi Jiri I just downloaded snapgear3.3.0 linux and tools from CyberGuard for LEON3. Then unpacked the linux sources and tools. I can not find gaisler (to choose...
... This message indicates that grmon did not detect any (working) memory, and did not set the stack pointer. You can try to start grmon with -stack <addr>...
Recently I met a very strange problem during the connectiong between the cygwin and the board gr-cpci-xc2v6000.The type of six proms in the board is xcf04s. ...
If the old .mcs files still work, you must have changed something in the template design such that grmon does not connect. Make sure that the AHB UART is still...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
