I have one of those Dell TV-out plugs which seem to only produce picture with no sound in windows (XP). More recently however, I can't even get that to work...
The clock function in both Linux and XP is playing up. Each time I start up the laptop, the time is wrong. Sometimes by a few minutes, sometimes by a few...
... I suggest asking for a Dell tech. I suppose your laptop is still under warranty, so you'd be a lot better this way. Here the clock is always right and my...
I don't get sound with the TV out either, I have a headphones plug with a cord that splits that into two RCA plugs (for left and right stereo), then I take...
Agreed on the recommendation for the tech, I've never heard a report of this before, and mine work just fine too (after a couple? three? years of nearly...
... shivers down my spine too. A linux server admin that shiver from compiling his own kernel :) Friendly greetings from a concerned server admin! [Non-text...
I am attempting to install Slackware on a Dell Latitute D800 and everytime it tries to load I get: Warning: unable to open an initial console Kernel panic: No...
I don't run slackware, but I imagine people will need to know what version of slackware, what bootloader you're using, and how its been installed and...
Think I might have found the problem...lilo.conf had the root pointing to a non-existent drive. Re-doing partitions and installation as i type on other pc. ...
On to new problem...now it says: sg-2021: reiserfs_read_super: can not find reiserfs on ide0(3,3) Kernel panic: VFS: Unable to mount root fs on 03:03 ... with...
You are far afield from D800 problems, it appears :-) I don't use Reiser either - I'd suggest a slackware install list if there is one - as these all seem...
I cannot seem to get the ethernet port nor the wireless care to become recognised. I do have the tg3 module runnig for the ethernet but it still will not come...
What kernel? The tg3 module should recognize it out of the box - its a broadcom 5705M chip if I recall correctly and support for it is built in to modern...
My laptop uses Fedora Core 3. This morning I got all the latest updates using yum, including kernel 2.6.11-1.14_FC3. I installed this, together with latest...
I had a similarly bad experience, using a similar software setup (nvidia and vmware kernel modules, no madwifi though) I'm still on 2.6.10-1.770_FC3 Thanks for...
So far I've been able to figure out how to get SUSE 9.2 up and running with all my hardware, (thanks to search) but this one is stumping me. Really stumping...
Easy - just run unencrypted and do OpenVPN over it. Your neighbors will love you. Honestly, I'm not sure - I haven't used WPA at all but I just got hardware...
I've successfully used wpa_supplicant with my Linksys WRT54G router and Truemobile 1350 wireless card. However, I am stuck on using version 0.2.7. If I use any...
Did you configure the interfaces? ifconfig eth0 <ip> netmask <mask> up Do you have dhcp server? dhclient eth0 Do you see traffic? tcpdump -n -i eth0 -V...
Yeah, it was actually the fact that the default gateway interface was set to the wired ethernet plug eth0 instead of the wireless eth1. Mostly I solved all my...
Hi all, I have just installed SuSE 9.2 Professional (kernel 2.6.8-24-default) on my new D810. Installation was done following the default recommendation (no...
Even though the mailing list archive interface is a little crusty (you have to search, then page through lots of pages even if there is only one result on each...
... Haven't had coffee yet :-). Hopefully you got from this that the word "suspend" was in *either* the title or body. Its the magic word to search for,...
So I've got lineakd working with my volume buttons, but it ends up changing the master volume, which only has an effect for the laptop speakers. When I plug...
... There are a few simple examples of using volume buttons, if you're into C/C++ programming you might want to look at them. -- Best regards, Engin AYDOGAN...
Hi. ... Instead of attaching one of the actions offered by lineakd to a key, you can simply specify a shell command to be executed. E.g., instead of using...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
