You can test for yourself whether it is open drain. When the processor is not in reset, use a 1k pull-down resistor on the pin. It the output goes toward and...
Hi All The problem with my olimex-arm-usb-ocd with olimex lpc-mt2106 board has be fixed. It turns out that the problem was in the hardware. Initially I powered...
Hi, eLua is an open source effort to bring the Lua programming language in the embedded world (MCUs). It is meant to be a complete MCU development environment....
Hi Martin and Marcus, Swapped +1.8V and +3.3V is a real bummer. I've also added a level shifter to convert the clock from +3.3V to +1.8V. A suggestion to use...
Hmmmm.... Looks like you are right. I checked this on my two different 2368 CPUs. One is running at 48MHz and another is running at 72 MHz. Regardles of...
... Strange isn't it? Sure seems like the kind of thing that ought to be documented somewhere. I set up another timer with the prescaler set to 0, just to...
Hi, I want to use an ULN2003A (got suggested here a while ago as a good LED driver). Can anyone confirm that the ULN2003 works with the 3.3V output from LPCxxx...
Hi Bob, Just a clarification as I've recently just delved into this. The CPU is restricted to 60MHz or below as stated. The 48MHz CPU speed comes about if you...
... To follow up, accessing the APB (LDR) takes 13 cycles across the board, except for the RTC area where it takes between 25-28 cycles. That's pretty extreme...
... LPCxxx I/O pins? Yes, that is what we are using. (at 25C ...) ULN2003A needs a maximum of 2.4 volts (for 200 ma) and the LPCxxxx generates at least 2.9. ...
... The 60MHz limit applies to execution from FLASH. All my tinkering is done while running from RAM so I go for the 20% speed boost. :-) I realize I'll ...
Dear Sirs I need some help in exemples for programming for LPC 2103 using Workbench IDE and inteface with IAR LPC2103 mini dev kickstart borad. All help will...
... Are you getting this one? http://www.iar.com/website1/1.0.1.0/658/1/index.php?item=prod_prod-s1/200&group=prod_prod_grp-s1/34 It has already the hardware...
hi, Ashwin I met a issue of stability in LPC VirtualCom. For example: i open HyperTerminal and send "1" to device to light LED. It's ok. Then i send "1"...
I have LPC-P2124 Protoype board made by olimex and an ulink2. My question is: If I push the reset in the board while I debuging with ulink2. this generate a...
Hi, thanks for the answer, this sounds good. Does it matter whether we use the ULN2003A or the ULN2003AI (second one has a serial resistor of 2.7k on series...
Jumping to zero location. Interrupts and some peripherals may stay initialised in this way. ... [Non-text portions of this message have been removed]...
Hi Vincent, I have never encountered this issue. Did you try the USBIO demo application? Warm regards Ashwin Founder, NGX Technologies Pvt. Ltd. Bangalore-...
Hi, does anybody has port of LWIP for Embedded Artists LPC2468 board (Micrel Phy)?Can you please share the code for experimentation?Any clue in this regard...
... They are not documented yet, because NXP originally though it will never be neccessary to use something different than the default values and the risk for...
... ok, I assume "nit-picking" is the correct word for you ;-) - this is what the www.dict.cc says - I agree that adding one "e" sometimes changes the meaning...
Nah, I'm not nit-picking. Some typos just strike me as funny. As for "femalefunctions", do you really want your code getting moody and snapping at you for no...
... one has ... I think if you look closely you will see that they both have a 2.7K resistor in series with the base. ... I'm assuming that you have: V+ ->...
... (never ... know ... to ... different ... I asked NXP about this and they said that the nominal value, before trimming, is 0xA0, but each is factory trimmed...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
