I made myself a lpc2104 board using Leon Kellers design.Now i want to test the board.Can somebody tell me how to program the chip.Also i want a simple program...
... From: "Gopalakrishnan" <naray23@...> To: <lpc2000@yahoogroups.com> Sent: Tuesday, February 01, 2005 8:20 AM Subject: [lpc2000] start with Board ... ...
Hi All I am presently working on an Ethernet extension for the LPC2106 with the Freescale (Motorola) MC9S12NE64. I bought 5 pieces for about $12 a piece in 80...
... Not quiet right. I just looked up on datasheet at Ramtron. The max. bus-freq. is 1E6 Hz for a 256KB FRAM. 20bits to read memory => max. 50000 reads/s The...
Hi all, I intend to use a "14.7456MHz HC49US/THT" type of quarz for the oscillator. However with 2 x 39 PF caps, it seems to be hard to find an appropriate...
Hi, 39pF caps sounds awfully large in my ears... try 15pF Regards Lasse ... From: Markus Meng [mailto:meng.engineering@...] Sent: 1. februar 2005 13:10 ...
Hi everyone, I'm having some problems using the 2nd CAN controller network on the LPC2129 ARM board. So far I have successfully used the 1st CAN controller and...
Hi Owen, Yes, this helps a lot. Thank you! Martin ... you read - modify - write) I had lots of spare flash and was typically saving a configuration just a few...
Hi Owen / Martin, Maybe it's also worth to point out that you can emulate EEPROM closer by "spreading" the data in Flash, and leaving markers - although I'm...
Does anyone know of a Yahoo group for the ADI ADUC70xx ARM CPU? I could not find one by searching, but the search facility in Yahoo groups is not very good....
... fastest ... This ... I was searching the microcontrollers category and most of the groups that have more members are PIC related. In fact, the group with...
A new Yahoo group has been formed to support the ADuC70xx ARM MCUs. http://groups.yahoo.com/group/ADuC_ARM/ If you are working with these parts, or have an...
Anyone have any ideas when tools and samples of the ADuC70xx will be available? I'm not overly happy with the need to go to higher end parts with the LPC to...
... I am getting samples right now. I asked for 5 of the wide temperature range version ADuC7024BST62 which they are sending along with 3 of the standard temp...
On 31 Jan 2005 at 5:07, Rick Collins wrote: [Lots of stuff snipped] ... No the W3100A does support 100 base T. Although you need a seperate PHY and of course...
... The comment was wrt philips parts. From the first seminar it struck me that even the smallest parts were overburdened with memory and comms peripherals,...
Al, when you wrote this "Whoops, sorry, thought I weas replying to that group, should read more closely." You actually had the option to do exactly that,...
Hi Martin, there has been a thread a while ago with the title "Partial Flash Programming" which you can use to do a search in the archive. In particular there...
I am working on a scheme to update the code in an LPC2106 via Ethernet. The application is done and working, I have connection to the host via ethernet. I...
I finally got to the point of shutting down the LPC2138 on the Keil development board. Battery life is critical to my application, therefore I need to verify...
... Jump table? If you place a vector table of functions at a fixed place in the download area it can be replaced repeatedly. I suspect you will need a fixed...
... Unless you really need some speed. You said it interfaces by I2C which is very slow by comparison, ~400 kbps vs. >10 Mbps. I don't plan to sell the board...
Tim, I guess the 350 mA (the "m" should be a "u")was a typo. What you measured in power down for the RTC is correct between 15 and 20 uAs. Logic in this...
Hi, I was wondering if anyone has any information regarding the secondary JTAG - internal structure. I'm battling a problem that I can only connect to JTAG ...
... purposes? ... only ... Ho, I've implemented an eeprom emulation for a LPC2106 in my "T-Clock"- project. In the application it's just used to store two...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
