Just uploaded 1.38 which added support for this using the -wipe parameter. --Ray ... protection. ... step ... like ... newer ... CompuPhase)" ... adapted ... ...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the lpc21isp group. File : /Beta...
lpc21isp@yahoogroups....
Jan 12, 2007 6:37 am
126
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the lpc21isp group. File : /Beta...
lpc21isp@yahoogroups....
Jan 22, 2007 7:37 am
127
Hi, Wondered if anyone had experience of problems with -term and -termonly under MacOSX. Specifically it seems to local echo back characters. (Is this intended...
Arthur, Good idea, but no - I don't think it's anything to do with the serial baud rate at all; these are some results that might help show why I think that: *...
Rob, ... There was a baud rate bug in earlier versions of lpc21isp on Mac OS/X, including 1.33. The latest version is actually 1.39, and you can find it at...
Arthur, I built 1.39 on the 21st of this month and am currently using that. I've been using 115200 for programming for over 6 months with 1.33 and 1.39 - I...
Hello Rob, ... also get extra or ... perhaps to find out if it is a LPC problem or an USB / Mac problem: Can you leave the LPC disconnected and shortcut RxD...
Hi, I think it's a mac problem. It echos without anything connected to the serial port at all. I will try the hardwired shortcut when I get 5. I expect to get...
Rob, I just built 1.40 from source and am still limited to a baud rate of 38400.. anything above this rate will not sync. Bootcode version: 11 Arthur ... From:...
... I don't actually see any changes in the serial code for Mac OS X between 1.33 and 1.39. I see changes between 1.32 and 1.33. ... I'm guessing the Boot...
Hello Rob, which crystal do you use on your board ? Pay attention that (at least the boot loaders i know) don't use the fractional baudrate generator (which...
... 14.7456 MHz. ... It says I can use up to 230K ... although it makes me wonder what they mean by "11500" and "230000" looks like they approximate from...
Rob, am using a 12.000 crystal on a LPC2148. The table in the user manual gives a 12.2880 frequency translating to a max baud of 38400. This is consistent to...
... echo ... same ... changed the ... I just made a small test (as I usually use lpc21isp in term mode only to display messages, almost never to send text to...
Hello Jean-Marc, ... I think it was implemented in that way just out of simplicity. You have two function, one for checking and one for getting characters. ...
When the next person does an update, can you please fix my little mistake in the parsing of the wipe parameter There needs to be an else if following it...
Hi, Process type question... Just patched the sources with a command line option to locally echo keypresses. Should I post this to the files section? Regards, ...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the lpc21isp group. File : /Beta...
lpc21isp@yahoogroups....
Jan 28, 2007 10:45 pm
149
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the lpc21isp group. File : /Beta...
lpc21isp@yahoogroups....
Jan 29, 2007 7:05 am
150
Hi,capiman. When I use -wipe parameter to wipe and program a NXP device, the lpc21isp will erease the sectors, to be programmed, again separately. It wastes...
Hi anybody used lpc21isp with LPC2148 chip I tried to use it with Olimex LPC2148 Dev Board, it can detect the Part ID as 67305253 and the bootloader version as...
Hello, ... Part ... i program an embedded artists board with a LPC2148 on it with lpc21isp (at the moment i use version 1.43, unmodified) without any problems....
here is the logfile of the trial of lpc21isp with -wipe -debug option turned on Thank you eveyrbody for trying to help ################# logfile begins...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
