Thank for this I should have checked before asking. The RS part number is 484-0509 and the website is incorrect the correct website is: http://rswww.com/ ...
Hello everyone, I am Deepak here. Though I am not very new to 8051 I have never used LPC's. I intend to use it in an application requiring two comparators. I...
... programming ... Hi Deepak, There are the datasheets, but to "get your feet wet" in the minimum amount of time, use Code Architect to generate your code,...
I can program my lpc936 when inserted on mcb900 also can program lpc938 but i cannot program lpc922 with icp using the aplication note circuit and isp-icp...
... The ICP specifications should be in the files section. Check if the reset and VDD match the ICP entry requirements. It is possible that board capacitance...
Dear Sirs, We want to introduce LadderWORK for 8051 Automation Software LadderWORK allow you to transform a generic 8051 processor into a PLC (Programmable...
I write it for the first time. I'm Beginner. I made C-source that was compiled by KEIL uVision3. Output-file is OMF(*.omf). PDS51 made New project and selected...
... Good on you - we all start somewhere. ... My PDS51 does not have an entry of 'standard OMF'. I am aware that there are a number of emulators in the PDS51...
... I have use PDS51E(ver,4.46) this version has an entry of 'standard omf', because Help menu has KEIL object handling. ... My debug files are in the same...
Dear LPC9xx subscribers, I developed a powerful LPC9xx programmer which supports both ISP(if chip has such feature incorporated) and ICP protocol to program...
Hi, you describe a problem that is listed in the Data Sheet and in the Errata Sheet. While I agree that this can be an issue for some applications, the Errata...
IMHO stating "reset is flawed" and "workarounds are available" is nice, but I would also expect upgrades to the chips with corrected known problems. I see...
I did not wanted to be polemical, nor I wanted to start a flame. I should say that I 100% agree with Jan: the purposes of LPCs can be disattended with this...
This problem is not specific to Philips. I'm using a Microchip (not by choice!) rfPIC12C509 that exhibits this same problem. If you reapply power to it while...
Tom, here is what you are missing: If you switch off power, the voltage in your system will go down to a threshold of a diode drop rather rapidly. So the range...
this is a email / a reply from Embedded Systems Academy ... Hi Harald, Version 2.40 of Flash Magic is now available that supports sending the CCP command. Go...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the lpc900_users group. File : /v15 ISP...
lpc900_users@yahoogro...
Oct 26, 2005 7:12 pm
181
Hi everybody, I would like to introduce my LPC900 programmer for all of you who, like me, are fascinated with the Phlips micros. My program has the ...
hi Andy, isp to icp bridge version 1.6 is available now! you can download it on the website: http://www.esacademy.com/software/flashmagic/ Best regards! Frank...
hello, I want to know about UART performance. (1)In case of LPC900 series Microcontrollers use UART, How much will permissible range of error margin? (2)The...
Hello, the permissible Error margin combined over the transmition of a byte including start and stopbit has to be less than half a bit. Half a bit is 50%,...
Enter your vote today! A new poll has been created for the lpc900_users group: Do you use ISP or ICP for your LPC900 design? o ISP o ICP o Already programmed...
lpc900_users@yahoogro...
Dec 13, 2005 3:33 pm
188
Dear LPC9xx Users. Take advantage of one of the most powerful micros in the market, the LPC9xx. There is not reason to stay outside this fantastic world. The...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the lpc900_users group. File : /USB-ICP...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
