Hello people. I've written an ICP programmer for use with our philips-based products, for use in our mass-production environment. I've based it on both the ISP...
Thank you John, Can you e-mail me a diff off-line or to this list and I will update source forge CVS with the changes. Let me know if you get it working as I...
Hi All, Does ICP (Serially Clocked) have supperior features over ISP (UART)? Obviously if you use ISP you need a stable clock source. If you program the flash...
I put the files in a temp directory in the Files section of the group. I'll try the program out next week and let you know if I get it working. ... went to ......
I've checked in the ICP PDF, and I've figured it's the configuration byte at 0x03 ("Status Byte"). I'm already programming it to 0x00. Either that's not the...
Hi Oren, Are the config bytes written correctly? If you read them back, do they have the correct value? They are NOT included in the CRC, and you'll have to ...
Hello Eric, Sending the CCP seem to solve it. Thank you. ... they have ... have to ... a device ... That is ... configuration ... the ... (and ... it ... ...
Hi There, My project is building a simple router with MCB900, So the 8-bit data is input from RS232, then it has to route [output to correct port] it to some...
Rod, I haven't been able to program anything yet. Can you give me an example of the command line arguments used to program or put the device in ISP mode? Also,...
John, I have never used this under windows except when I was doing some early testing for a friend of mine. I use the following commands to erase the necessary...
Gertjan, Hitesh, I have also had problems using ICP when following the appl.note AN10258_2. Like you, Hitesh, I found out that the application board VDD...
All, I am using the ISP to ICP bridge based on MCB900 from Keil to program a PCB-soldered LPC936 (TSSOP). It is possible to read the device ID, to program user...
Hi, once I have had similar problems. See at http://www.esacademy.com/software/flashmagic/forum/read.php?f=1&i=2564&t=2561 Now, I am happy. Regards, Johnny...
Hi Johnny, thanks for your hint. I've checked the message. Unfortunately, it was not the same problem. I could establish communication every time I wanted -...
Need some help with the LPC901 and data flash storage. I'm using pin 7 as s digital input to determine when power is going to be lost. The hardware is setup...
... Hi there, I doubt that the location is being corrupted as power is reapplied. If this were possible then there is a greater chance of a valid program ...
Phoebe, Thanks for the feedback. I'm using the "C" program examples provided in the LPC901/902/903 Users Manual for reading and writing to flash. I wish you...
... Hi, there is a LPC2000 Yahoo group http://groups.yahoo.com/group/lpc2000/ which is perfect to post your question but here is the answer: Go here:...
Hi everybody, I´m a new LPC900´s user and i´ve got a little problem, When I use the T0 pin as a simple output pin to drive a load (on/off), The CPU stops ...
Which LPC900 are you using. Larry Hi everybody, I´m a new LPC900´s user and i´ve got a little problem, When I use the T0 pin as a simple output pin to drive...
... Intel microprocessors Pic microcontrollers ... Service. ... What mode are you using, 16-bit timer or 16-bit counter? Are you using the timer to toggle...
It could be hardware or software. Look at the timer block diagrams in the user's manual. The Int0 pin can cause the timer to stop if the software is setup to...
Hello to everyone! I need help and/or suggestion to realize a smart load cell(classic wheatstone bridge) using an LPC917. The system needs 14 bits resolution...
Greetings to the group, i've already sent this to the Philips support, but i guess it isn't hurt to post it here also. There's something going on at the '931...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
