Hi all! I have P89LPC932 Rev C, and I can\'t reprograme using ISP again, I using FlashMagic to load hex file from example Hello <Keil Software...
keilsoftware@...
May 10, 2006 10:47 am
301
Hi ! I checked the total power down code execution on LPC932A1. It worked. When I transfered the code to LPC902 (I made some changes regarding ports init), it...
... using FlashMagic to load hex file from example Hello <Keil Software c51/Example/Philips/Hello/> to micro, but then, micro can\'t enter ISP again, although...
... Maybe I have met the problem with ISP circuit, can you give me a ICP circuit? Thanks before!...
keilsoftware@...
May 10, 2006 6:07 pm
305
... again, I ... but then, micro can\'t enter ... it. ... (owerwritten) ... -~--> ... See how. ... --~-> ... ICP circuit? Thanks before! ... It is possible to...
... P89LPC932 revC ín't support enter ISP by Hardware (3 pulse reset), and in datasheets, this micro isn't support for ICP....
keilsoftware@...
May 10, 2006 8:51 pm
310
I have a target with a TSSOP28 footprint (for P89LPC936FDH). I want to connect the EPM900 emulator (DIP28 footprint). Where can i find this adaptator...
Can anyone supply the source code of the isp_to_icp_bridge?the version v1.7 hex code was already uploaded to -->http://www.esacademy.com. Thanks in advance! ...
It seems that the bondout chip on the EPM900 is a 89LPC932. The LPC932 don't have analog fonctions and is code limited. Is there a boundout chip for the...
I want to use the ADC in the following mode : Fixed channel, single conversion mode. I don't understand what to do to trigger the conversion (write 01 to ...
If you order an EPM today it comes with a 935 and a 936 as emulation chips. Te LPC932 can be emulated with the LPC935 (real superset). If you have your EPM900...
Can someone supply the source code of the isp_to_icp_bridge?The version v1.7 hex code was already uploaded to -->http://www.esacademy.com. Thanks in advance!...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the lpc900_users group. File :...
lpc900_users@yahoogro...
Jun 6, 2006 4:19 am
320
Dear ALL, I try to use SPI function with LPC932. Transfer was success. Data is watched on MOSI pin. However, receive was fail. Data is not watched on MISO pin....
Hi, I have interfaced a 89LV51RD2 to 89LPC932 using SPI. For this I had to spend some time tweaking register values till it worked. However the data received...
Dear Pramod, Thank you for your advice. This problem is solved. Peripferal has problem. It was able to communicate bySPI. regards, ... be ... is ... the ... a ...
I'm trying to use the 913 device with 16MHz crystal (assured officially by Philips it's a valid configuration despite max. 12MHz on the DS). Only simple bit...
I am working on LPC 900 series, but am unable to find a source for the devices in small quantities. I need LPC902, LPC925 etc. in New delhi, India. If you have...
Max, Why don't you try another, lower frequency, crystal? That will at least check your firmware. You could post your code here so we could check it too. Let...
Hi. I am using the following code, mostly from the datasheets. I simply want to write a byte in flash. I cannot test this code using my Keil emulator, it is...
Please let me know how to join the LPC2106 users group. I am unable to get that link With regards Nagaraj ... Yahoo! India Answers: Share what you know. Learn...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
