Hi -- I just joined this group and am looking for some feedback. A) To program (write programs for) the LPC9XX which compiler do you find better 1) SDCC or 2)...
I used both, and I can say that depends on your knoledge an target: if you want to hava a free tool, you have to choose SDCC and will have also a lot of ather...
Hi! The LPC935 has two DAC outputs. I thought it would be nice to use those DACs in a new design. I've done some testing with DAC and it works... well, in some...
. . . ... . . . Hi! Thanks for your reply! It was a configuration problem. The digital output driver was still active. I wrote to the wrong register :-( It's...
... I reply myself: ID2 = 7AH sometimes reading the manual helps... ;-) ... I reply myself here, too: 1K sectors. The ISP protocol has commands for 16 sectors...
For LPC954, the MFGID = 15H, ID1 = DDH and ID2 = 7AH. And sector size for LPC954 is 1K. Good Luck. Finn To: lpc900_users@yahoogroups.com From: faumarz@... ...
Dear sir, I want to join lpc_900 group.presently i am working on lpc924 controller. I am facing problem during ISP programming.first time when i give supply...
i am facing problem in ISP programing in lpc924 controller.First time when i gave supply to controller in flash magic then it was automatic detact the...
Dear Chetan, First time you able to program becuase of Factory defualt ISP. At that time BSB bit is set from Factory. Once you program the Microcontroller...
Thanks Nilesh for giving me very useful information. But in hardware activation method what type of haraware addition is required.please give me schematic of...
To activate ISP via HW, you have to choose DTR and RTS usage inside FLASH MAGIC settings. Hw side, you need an MCB900 board or you have to build an equivalent...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the lpc900_users group. File : /USB...
lpc900_users@yahoogro...
Dec 12, 2007 3:55 pm
461
Hi, I have a problem with programming P89LPC922. I use ISP, i can programm it 1 time then i cannot programm it again. If i change the processor, i can programm...
Dear , You are able to program it first time becuase of Factory Programmed ISP setting.. I mean to say BSB (Boot Status Bit) = 1. Once you program it will be...
Dear Nilesh, Can I get a copy of your: Parallel port circuit.... And application software? Thank you very much, John W. Poore ________________________________ ...
... - You don't send a break on the serial port before starting ISP - You have not configured and activated in your firmware the serial port for break...
Dear, I met the same problem when I used P89LPC932. The solution of the "1 time program" is to set BSB(Boot Status Bit). This problem will happen when you use...
Min Zheng
minming.zheng@...
Dec 20, 2007 1:14 am
467
Dear Nilesh, Thanks for your advice....I have been using ICP method for the past some time and it works properly. ISP is somewhat limited, so either ICP or...
Hi, I want to design my own programming board for a LPC936 micro ( the postage and duty charges to get a ready board in India are outrages). I am more...
... postage and duty charges to get a ready board in India are outrages). ... with USB interface. ... Try it now. ... The ICP spec in the the "files section"...
See the following URL for a USB programmer to ICP http://www.lpctools.com/index.asp?PageAction=VIEWPROD&ProdID=83 ... outrages). ... Mobile. ... board, ... ...
There are several ICP options, one of which is available internationally from Digi-key; http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail?name=622- ...
for USB - check www.teamfdi.com ... postage and duty charges to get a ready board in India are outrages). ... with USB interface. ... Try it now. ... The ICP...
I hav been working with the LPC935 for some time and would like to use the DAC0 output - But it would not work !! The reason was - I was using the MOD935 file...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
