Hi, I´m currently working in a development for a hand-portable system, using features of the LPC family ( low power, low consumption ). I´m using LPC936 (2...
sorry,i redo the mail, I believe that the information was a little useless. I´m currently working in a development for a hand-portable system, using features...
Hi jamr, have you checked the user manual UM10116? I havn't used ADC with the LPC936 yet. But if I understood the description of "Table 18: A/D Mode register B...
... description ... description" on ... block at ... [mailto:lpc900_users@yahoogroups.com]Im ... useless. ... incorrect ... work ... You can not use the ADC...
Your probably trying to read multiple A to D channels at the same time . There is usually only one A to D per a group of channels so you can't read two...
Hi, i think it is pretty clear what i want. I want to read characters from the UART and stop reading if the character 'a' occurs. I have written a small...
Hi, you should initialize char character before entering the while-loop! ... i=0; character = 0; do{ ... The first time you call Get_Return_Value() character...
Problem solved for DAC0-AD00 in LPC936 I have solved the problem, I find a solution for my application: AD00 isn't a critical time task, I check the system...
Hi, does anyone have experience with the Vinculum VDIP1 module? I tried to plug several different USB disks into the VDIP1 module, but only one USB device...
Anyone done ISP on a 936? On the app. note AN10258, there is a statement that says 'To control VDD, a PNP transistor is needed, because P2.3 cannot supply...
... to ... No, you must build it as stated, it is part of the timing for entering setup to the device. Build it exactly like the app note and it will work...
... control ... enough ... P2.3 ... and ... I've seen it do that, I guess the logic is that it can do an ISP without the system power on. I've seen it light...
Google should help out quite a bit. ... -- Sutton Mehaffey Lookout Portable Security 4040 Royal Dr. #100 Kennesaw, GA 30144 800-207-6269, 770-514-7999,...
Sutton Mehaffey
sutton@...
Feb 7, 2009 11:42 pm
590
hi  this the first time i am using this controller P89LPC9401. i write a simple program to blink LED but it not work. i used P00 and P21 and configered as...
USE PUSH PULL configuration[current sourcing mode] or open drain[LED pull up- current sinking mode] More details in port configuration of usermanual Regards ...
Hello, I´m coming back !! I´m working with the precma LPC900ICP programmer board, and his own software. I need (I WANT) use flash magic (embedded systems...
I use LPC PRO with In Circuit direct download. APSTRON LLC P.O. Box 10336 Blacksburg VA 24062-0336 www.blacksburg.net/~schmitta ... From: Juan Antonio...
We are providing shipments for the programmers for ISP / ICP for the ARM/LPC9xx/8051 cores. few Programmers are compatible with the flash magic and few have...
Hello folks, Can anyone recommend a easy to use an eval board which has ARM 7. The kit should have a software which I can download and write code in C. Thanks...
... Hi Jennifer, might want to ask this question on the LPC2000 Yahoo group. But for starters, the best kits I know are from www.embeddedartists.com search for...
you may also get it from the www.potent.co.in and www.keil.com potent board has advantage of header, good after sales support and good pricing. regards, ... --...
I use a keil software EPM 900 and keil µvision 3 to program the P89LPC936 Philips microcontroller. The problem is when programming the P89LPC936 I get this...
I use a keil software EPM 900 and keil µvision 3 to program the P89LPC936 Philips microcontroller. The problem is when programming the P89LPC936 I get this...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
