Anyone done ISP on a 936? On the app. note AN10258, there is a statement that says 'To control VDD, a PNP transistor is needed, because P2.3 cannot supply...
... to ... No, you must build it as stated, it is part of the timing for entering setup to the device. Build it exactly like the app note and it will work...
... control ... enough ... P2.3 ... and ... I've seen it do that, I guess the logic is that it can do an ISP without the system power on. I've seen it light...
Google should help out quite a bit. ... -- Sutton Mehaffey Lookout Portable Security 4040 Royal Dr. #100 Kennesaw, GA 30144 800-207-6269, 770-514-7999,...
Sutton Mehaffey
sutton@...
Feb 7, 2009 11:42 pm
590
hi this the first time i am using this controller P89LPC9401.��i write a simple program to blink LED but it not work. i used P00 and P21 and configered as...
USE PUSH PULL configuration[current sourcing mode] or open drain[LED pull up- current sinking mode] More details in port configuration of usermanual Regards ...
Hello, I´m coming back !! I´m working with the precma LPC900ICP programmer board, and his own software. I need (I WANT) use flash magic (embedded systems...
Hola Juan Antonio, Soy de Colombia y trabajo con los micros LPC900. Si te puedo ayudar me indicas en qué y con gusto te ayudo. Si necesitas un programador...
I use LPC PRO with In Circuit direct download. APSTRON LLC P.O. Box 10336 Blacksburg VA 24062-0336 www.blacksburg.net/~schmitta ... From: Juan Antonio...
We are providing shipments for the programmers for ISP / ICP for the ARM/LPC9xx/8051 cores. few Programmers are compatible with the flash magic and few have...
Hello folks, Can anyone recommend a easy to use an eval board which has ARM 7. The kit should have a software which I can download and write code in C. Thanks...
... Hi Jennifer, might want to ask this question on the LPC2000 Yahoo group. But for starters, the best kits I know are from www.embeddedartists.com search for...
you may also get it from the www.potent.co.in and www.keil.com potent board has advantage of header, good after sales support and good pricing. regards, ... --...
I use a keil software EPM 900 and keil �vision 3 to program the P89LPC936 Philips microcontroller. The problem is when programming the P89LPC936 I get this...
I use a keil software EPM 900 and keil �vision 3 to program the P89LPC936 Philips microcontroller. The problem is when programming the P89LPC936 I get this...
Hi I am using LPC938, I am trying to get the UART's baudrate to 9600 but nothing seems to work..I the following code and all I see on hyperterm is just various...
clock is internal clock of 7.363MHz. I tired this code. Didn't work either. ________________________________ From: lpc9xxbeginner <schluchti@...> To:...
ya, I am trying not to use an xtal clock cos alot of the code is written and when I do the maths TH1 should be 0xFD to be transmitting at 9600 but its not....
Dear Sameul, Why dont you try the codes with code architect for NXP uC? Sincerely, Dhans Mob:+91-98867-30835 ________________________________ From: Samuel...
This is very old problem This was the problem which has made my visit to China :). Use 0.1uF between VCC and GND. (near to VCC pin of LPC938) Also check your...
Hi Samuel You may have got it going by now but here is some info. I used an LPC925 which I believe is similar as far as the UART is concerned. I set the txd...
Hi - I am using the LPCPRO programmer. It worked fine before with the P89LPC932A1FA. Now it is telling me it can't read the chip's Device ID (00 00 00). I am...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
