hi  this the first time i am using this controller P89LPC9401. i write a simple program to blink LED but it not work. i used P00 and P21 and configered as...
USE PUSH PULL configuration[current sourcing mode] or open drain[LED pull up- current sinking mode] More details in port configuration of usermanual Regards ...
Hello, I´m coming back !! I´m working with the precma LPC900ICP programmer board, and his own software. I need (I WANT) use flash magic (embedded systems...
I use LPC PRO with In Circuit direct download. APSTRON LLC P.O. Box 10336 Blacksburg VA 24062-0336 www.blacksburg.net/~schmitta ... From: Juan Antonio...
We are providing shipments for the programmers for ISP / ICP for the ARM/LPC9xx/8051 cores. few Programmers are compatible with the flash magic and few have...
Hello folks, Can anyone recommend a easy to use an eval board which has ARM 7. The kit should have a software which I can download and write code in C. Thanks...
... Hi Jennifer, might want to ask this question on the LPC2000 Yahoo group. But for starters, the best kits I know are from www.embeddedartists.com search for...
you may also get it from the www.potent.co.in and www.keil.com potent board has advantage of header, good after sales support and good pricing. regards, ... --...
I use a keil software EPM 900 and keil µvision 3 to program the P89LPC936 Philips microcontroller. The problem is when programming the P89LPC936 I get this...
I use a keil software EPM 900 and keil µvision 3 to program the P89LPC936 Philips microcontroller. The problem is when programming the P89LPC936 I get this...
Hi I am using LPC938, I am trying to get the UART's baudrate to 9600 but nothing seems to work..I the following code and all I see on hyperterm is just various...
clock is internal clock of 7.363MHz. I tired this code. Didn't work either. ________________________________ From: lpc9xxbeginner <schluchti@...> To:...
ya, I am trying not to use an xtal clock cos alot of the code is written and when I do the maths TH1 should be 0xFD to be transmitting at 9600 but its not....
Dear Sameul, Why dont you try the codes with code architect for NXP uC? Sincerely, Dhans Mob:+91-98867-30835 ________________________________ From: Samuel...
This is very old problem This was the problem which has made my visit to China :). Use 0.1uF between VCC and GND. (near to VCC pin of LPC938) Also check your...
Hi Samuel You may have got it going by now but here is some info. I used an LPC925 which I believe is similar as far as the UART is concerned. I set the txd...
Hi - I am using the LPCPRO programmer. It worked fine before with the P89LPC932A1FA. Now it is telling me it can't read the chip's Device ID (00 00 00). I am...
... Alvin, I have used the PDS900 from Acqura with some 932/935/936 designs: http://www.acqura.com/product.asp?products=PDS900 Keil also has tools for the...
Thanks Larry for your responce and information. ALvin..... APSTRON LLC P.O. Box 10336 Blacksburg VA 24062-0336 www.blacksburg.net/~schmitta ... From:...
please help,  i need the schmatic circuit diagram for 8051 kit programmer as in picture attached  best regards please help, i need the schmatic circuit...
... 30 seconds of googleing got me to http://www.mikroe.com/en/tools/easy8051a/ probably quicker than it took you to post the picture. The user manual shows...
Buy the LPC PRO. It works great and I think is less than $200.00 See: http://www.lpctools.com/lpcpro.aspx APSTRON LLC P.O. Box 10336 Blacksburg VA 24062-0336 ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
