Has anyone done up an assembler header file for the LPC903's? Sure would save typing in all those registers etc. If you have a sample init file then even...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the lpc900_users group. File : /MOD935 ...
lpc900_users@yahoogro...
Mar 6, 2005 8:03 pm
94
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the lpc900_users group. File : /935.ASM ...
lpc900_users@yahoogro...
Mar 6, 2005 8:09 pm
95
Hi Peter, I've just uploaded 'my' LPC900 series header file - written for the P89LPC935 - but will work for all the sub-series parts. It is in the files...
I've just been sent this link:- http://www.semiconductors.philips.com/pip/P89LPC938FHN.html Nice to see the increased ADC resolution now available in the...
Thanks for those files Dave. I downloaded a newer version of the metalink, used the header and template you sent and assembled my file. Now, here's the crunch,...
Hello all, I would like to ask you to do a little test for me (I don't have a single LPC9xx to try...). There was a discussion on 8052.com on the effect of...
All, I have just written and am using some code to program an LPC935. Would any vody else be interested it works on Linux and Windows compiles with Mingw on...
Hi Rod, ... What bootloader entry method do you use? Hardware activation (3x pulse on RST)? I would like to use it with a LPC932 though, so a few changes will...
It is very generic there are no limitiation with regards to the boot vector address or anything. I use the 3-pulses on reset to trigger entry into the boot...
... Unless you think you can make a lot of money out of it then I would recommend the GNU licence. At least that way others can extend it but it remains free. ...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the lpc900_users group. File :...
lpc900_users@yahoogro...
Mar 28, 2005 9:37 pm
118
All, There you go it is still a work in progress and I have placed it under the LGPL. Have a look and see what you think if anybody else likes it I may even...
Hi friends, Anbout six month ago when I started using LPC9xx chips with MCB900 and FlashMagic, I had taken good help from many of you. Since then I have been...
Hi Rod, Sure looks good, I'll have better look at it when time permits. Of course you will be the first one to know when I have any comments or fixes. Maybe a...
I do not task switch when I create these pulses and I have checked them on a scope and they are well within the spec. If you look a bit further down in the...
Hi Rod, ... I know, but the OS may very well decide to switch when the code in the timing loop... In that case you'll see delays from several ms to hundreds of...
All, This feedback is very good and explains why when I looked at other programming designs for the LPC micros the programming interface seemed that the the...
Hello to everybody I am using IAP to program the FLASH memory ,to store permanently some data, as I have not included EEPROM in my target board.So my ...
Hello Since it works on another board, I think your controller on the target board does not detect Power-Fail soon enough, for a erase and write cycle. Are...
Hello Pragnesh, this is a food and very important question and the answer is depending on some of your system paramters. 1. You can generate an interrupt only...
Hello Robert, I tried earlier but it did not work. If I put Large capcitor on power supply it will increase both raise and fall time of power supply. If raise...
I am having a problem using P1.6 as an output on the Keil MCB900 board. The port pin seems to be stuck or pulled low. I've confirmd that my code is setting...
I've developed and made an hardware/software kit that allows to program any Philips LPC900 Family Microcontroller derivate. It's named "LPC900icp" and works...
Philips is pleased to announce that Digikey now sells Philips semiconductors, including the LPC900 microcontrollers. Digikey currently has 10 LPC900 types in...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
