Hi, if someone have the book "The Magnetics Measurement Handbook" by Jack M. Janicke, it can be scanned (some hours of work!) and saved on CD. It's one way to...
I have a copy, but the problem is that it is copyrighted. Jack died July 2000 and his son inheirited the estate. I sent an email request Feb 21, 2005 to...
... But what difference does it make? Wouldn't I just orient the magnetometer 90^ east internally, and make the magnetometer look like it was pointing north? ...
Hasan, Yes, that would do it. The issue is how much sensitivity there is to a fixed angle change. Near the N-S line the sensitivity is very low. On the other...
Hello All I was looking into this kit--Questions - Does it come with instructions,is it easy to build,any more problems with lockups? I plan to use RSpipe Pro...
Hi Rob! ... Thanks re: site :-) More stuff will be added soon, but it's not ready yet ... neither the hardware, nor the page about it. Which kit are you...
Hi: I'm looking into ways to detect magnetized material, but not detect ferrous metals. US patent 3,165,691 "Method of Recognizing Industrial Wiping CLoths...
Hi Rob! ... Sorry, don't have the kit, so can't comment on it. But I'm sure Erich Kern of Fat Quarters Software can tell you about it. Erich ? :-) Best...
has anybody had any experience building one of these kits?I have the circuit board built and I am starting to mount it in a plastic box....I am trying to...
Mike, I'd use a 12 V. AA pack. The 5V regulators drop out at 7.5 volts which is a lot closer to 9 than to 12. By the time a 12V pack is down to 7.5 volts...
Thanks very much Erich,I really like the kit and hope to get the PVC this weekend....has there been any problems with the audio out ic going bad from plugging ...
Hi Michael, No problem with the audio IC. Did it go out on you? Your check bounced...insufficient funds. So, the bank charged me $20. Please send another check...
Sorry for the mix up.....my wife tells me the Bank messed up......I am very embarassed.....I will be leaving the group now and I am very sorry......mike ... ...
Hi Michael, You shouldn't leave the group because of this, it's a bank screw-up. However, I owe everyone an apology for having posted this to the magnetometer...
John: Have you any expereince on the long terms stability of the KMZ51 and the stability over wide temp ranges ? Regards ... come to mind. The variance of the...
I have done more work with the HMC series as I used to work for Honeywell in the oil exploration portion of the company. The KMZ51 is licensed under one of the...
HI all, I'm still using the HMC1022 ic, i had majopr problems with temperature drift. After alot of messing about & experimenting i found that the HMC1022...
John, I think we met once before when you were at QSI. I am doing a general review of AMR sensors. I have done many FG designs before. I want to understand and...
... If you use metal film or 1% or better precision resistors, you greatly reduce this problem. Carbon resistors have a terrible tempco, and it's negative. ......
Hello group: I'm still fairly new to this group and have just been lurking. Can someone tell me what this K-100 kit is and where there is some info on it? I...
Paul McClure wasn't it. I did not recognize your handle. Fluxgates have a lower noise floor by at least an order of magnitude. These are resistive devices and...
I built the EPE fluxgate gradiometer. I'm having problems with my top sensor. It either reads "zero", or it reads exactly the same as the bottom sensor. I...
To All, I replaced the capacitors on the sensor array and now the mag works great. If anyone else has this same problem, it is probably a bad capacitor or bad...
We lost the software for this logger last month when bag contain the disk was forget on the field. the Logger was not useful until the software is load to the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
