Hello one and all, I'm a novice in electronics, even if I wield the welder fairly much and often. This I do to make things for the slotracing I spend my days...
Hello all, I am from a research group that is currently involved in a project that requires us to measure the radio emissions from a storm down between 0.01Hz...
Signals from storms - Interesting topic. I would agree that a magnetometer sampling with say 5 samples per secs is the right thing to use (in principle...
leemanwebbstormlaboratory The magnetometer will work but has a limited dynamic range. Most available mags have a lower sensitivity limit of about a nT. There...
Hello group... I seek help with a SAM magnetometer in Sweden and hope to have it fixed before the ground freezes above the sensors when the winter comes :-) ...
Hello group: First of all - I am new to this group. My greetings to all members Jan: I am not familiar with your SAM magnetometer, but I assume X an Y stand...
Usially X is for N-S and Y for E-W (Z for the vertical component). Your SAM has 2 FGM3 fluxgates positioned N-S and E-W I therefore assume. Before a further...
Ciao a tutti! Free access to the "online journals of the Royal Society" for two month http://www.journals.royalsoc.ac.uk download as much PDF's as you can! ...
I'm working up a simple DC output magnetometer based on the FGM-3 with a negative feedback coil, to phase lock its output to a crystal oscillator. I could use...
I have been working on a magnetometer system based on the FGM-3, and have had to dig to find out many needed bits of information about it. I discovered by...
Not that I would know ;) , but there are certain solvents that will disolve the epoxy / potting of the FGM unit, and an air core works just as well with that...
I am getting ready to begin testing my FGM-3 based magnetometer that produces an analog output based on phase locking the FGM-3 to a crysyal oscillator with a...
I have made a first attempt at reconstructing the schematic of the FGM-3 magnetometer. The component labeled xray and schematic are in my photo album. ...
Hi John: Thanks for the X-Ray. When I tried it the result was not as good. I think you should have 4 coil terminals: L1, L2, L3 and L4. Two are for the...
... I deduced the connections I show on the schematic partly by a resistance measurement between ground and feed back pin (<10 ohms) and the recommendation...
HI John: I agree there are two coils, and it would be good to call the terminals L1, L2, L3 & L4. It might help to have an X-Ray taken with the unit rotated...
... The pairs of stacked traces are offset just enough that I can tell which is which for most of the branches. I think. ... Thank you. This should provide...
I just received my transparancy scanner from eBay and replaced the first xray of the FGM-3 with a better version in my photo folder. I also placed a file of a...
Folks, I'm sorry, but yahoo web services doesn't behave like it did in the fist days. So message posting, notices, etc. might take a little longer than...
YAHOO web services doesn't behave like it did in the first days. So message posting, notices, etc. might take a little longer than expected due yahoo's ...
I am new at this but just posted a circuit using the KMZ10 magnetic sensor with temp compensation. Unfortunately I have no means of flipping (but see how I can...
... how ... I think any OP amp as current source will work. I have some questions on your schematic. What is the amplitude on the connection line ? Why are you...
... The only difficulty in building a coil is to design a low noise and stable current source to drive it. I assume you just want to use it as an offset bias....
Thanks for your comments, John and Alexander, From your comments it is obvious I do not know what I doing. All I did was take the KMZ10 circuit from the app...
To aid in reconstructing the internal structure of the FGM-3, I have uploaded to my photo folder, scope captures of the feedback pin waveform, the supply...
... (snip) I did not meant to tell you that your circuit was wrong or bad, but just that you might be able to push a bit more signal to noise ratio out of it...
... I thought the same way. I found an op amplifier, made by Linear, LTC2050, however Analog's are also very good. I do not care about DIP packaging, but I...
... noise, ... (snip) ... I think, for this bridge source, an instrumentation amplifier configuration is most likely to provide a low noise, supply rejecting...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
