to do a position sensor set up, say a projection onto a floor, and everytime someone walked onto the projection area, it would, for a stupid example, draw a...
I posted this on the groups page, but i wan't sure if that meant it went to all users as well, so sorry if this is a repeat. It would be fairly simple with two...
Well, it seems to me like there's a lot involved even in getting the two position camera system set up to track motion reliably, but assuming you get that all...
Hey group; Ages ago, I posted a question about running 4 pots off the teleo board. I received a reply from a user called atiyana1 (message 938 on the list...
Pete Hindle
petehindle@...
Oct 27, 2005 6:52 pm
1030
It really depends... What's smoking? Some components can emit a tiny amount of smoke and still work, but most are dead when they're smoking. As for...
I've posted a picture on my flickr account - http://www.flickr.com/ photos/40281232@N00/56654174/ - which should tell you better than I could describe. As for...
Pete Hindle
petehindle@...
Oct 27, 2005 7:11 pm
1032
OK. You've been smoking the TVS diodes, which are there for the protection of the processor. They can smoke a little without dying. Once they're dead,...
... Okay - can I test them with a multimetre? What sort of reading would I get from a dead one? And how can I stick a replacement one back in? ... I thought...
Pete Hindle
petehindle@...
Oct 27, 2005 9:17 pm
1034
... A dead one will read 0 ohms or close to it from one side to the other. A good one will read a lot of ohms there (millions?). To replace the thing, you can...
Hey; ... No! Because I'm not trained in electrical equipment I'm really, really careful - I've been using the 5V output all the while. ... Measuring the...
Pete Hindle
petehindle@...
Oct 27, 2005 10:49 pm
1036
Well in fact with 1 installation of XP. The XMLSocketServer simply cannot find the Teleo Module (I've tried COM2 and 14). Hyperterminal works. Simply cannot...
Hello, I also have the same problem.I can not make Teleo MIO work under Windows XP.I have installed the driver of teleo and have tested it with the steps you...
Hi Onno - just a very quick reply, not addressing all your points... An oddity in Windows with the USB driver is that the machine will often not find the USB...
Sorry for the newbie questions! My interest was peaked with the phrase "Using a shielded piezo element bonded using adhesive tape onto a wide, elasticated...
Hello, I solved my problem.As I said my problem was with the hyper terminal which it said "another program is using the selected telephony device.Try again ...
does anybody can tell me when the Ultrasonic Distance Measuring Sensor will be avaible??? http://www.makingthings.com/products/products_future.htm please...
So my big sculpture is up and running (pictures soon), and after a few teething problems it settled down fine running off my PowerBook. But then earlier this...
Nathaniel - usually this means that the devices you are powering through the network are pulling too hard on the power supply. The power supply quits...
Thanks for the quick reply Liam, I would never have thought that the power supply dropping out would be to blame. Thing is I changed the system a bit, I am no...
Depending on how big the relays are, they could possibly be to blame. Do you have any of the specs for those relays, or do you have a meter with which to...
how would it be possible to connect and control say a grid of 20x20(400) light bulbs, controlling the brightness, or even just on and off, or what about 400...
Hello, I have also the problem of getting the sample button program work with windows. It doesn't return after the code line if ( TeleoEasy_Init( devicePath,...
Hi, I'm currently working on an installation in wich I want to control some sound elements(max/msp) and some visual stuff (flash) by my heartbeat. Although I...
Hi everybody, I just wanted to take a moment to post a story of winning with the teleo to this list, because sometimes I worry about all the projects that are...
Pete Hindle
petehindle@...
Nov 19, 2005 12:39 am
1053
Hello I am working on a project about real time rubber-stamping controlled by telio and Max. Meaning that by measuring pressure mapping it triggers differently...
hi I never used teleo for it but made some pressure maps out of piezo elements. I have an electronic drum at home and studied one of the pads, wich is a hard...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
