... Call for Participation: International Computer Music Conference 2006 Tulane University and the Newcomb Department of Music are proud to announce the open...
I'm not able to duplicate this, but we've heard of problems with COM ports above 4. Possibly Teleo needs to be told manually or in the code to use COM7. ...
I have a need to build/create an electronic circuit and/or device that does the following; I have lamps in series (looped) and they are wired so that each one...
Hi, Before we can help much, you'll need to offer some more information: 1) what kind of lights? (i.e. low voltage dc or Ac?) 2) are they really "seeing" each...
DW Thanks for the response. Here are some answers to your questions; 1) AC, 8hz 2) Sequenced, but not in the typical on/off/on what I need is a slight lag so...
hello/ I am using a 12v relay (with a teleo introductory module) to switch a small fluorescent strip light on or off (to simulate the patterns of light caused...
I don't think the relay is drawing anywhere near 2 amps, unless it looks like a relay for staring a huge motor. And the load circuit of the relay should have...
Don Day
don@...
Jan 10, 2006 2:58 am
1103
Thank you for the reply Don, The same thing happens if I increase the interval between turning it on of off (it will lose the usb after a few cycles), I have...
this is the error message I get in the max window Teleo Interface opened TI_put: write failed, errno 31 Teleo Interface closed TI_put: interface not open ...
You might try putting a capacitor across the relay. I've found that heavily inductive loads are sometimes hard on the microprocessor. Perhaps try 0.1uF, 50V...
does anyone know a good way to measure an existing voltage using the teleo intro module i.e. I have a sensor that outputs approx 2.5v when triggered, but I...
Not quite sure I understand your question James - are you trying to determine how to listen for the trigger from the sensor in software? If so, which...
hi liam/ I am trying "determine how to connect the sensor to the Intro Module so that it will read the voltage properly?" (sorry for the poor explaination) I...
I have cut two leads to the piezo-speaker (buzzer) on a smoke alarm and would like to replace the buzzer with the intro module so that I can get a visual...
Folks- I suspect this is something I am misunderstanding or doing wrong, but I'm puzzled by the behavior of a polyblock I've been playing with. According to...
Hi Steve - sounds like you may have gotten a sensor that is not wired up correctly. I would definitely not hook the sensor up again until it's either repaired...
Replaced the sensor and it works fine. Thanks. Onto the bigger challenge: I'm trying to read temperature changes in tenths or hundredths of a degree, but a...
Hi all, I need to track some movements on a stage, I read that you need a NTSC camera to use with the videomodule, could I use PAL cameras? Am I correct if I...
Apologies for cross posting MA in Digital Performance School of Arts Brunel University West London Course Convener: Paul Verity Smith This is a distinctive and...
Hi, I'm building a new project here, and I am in need of locating a decent (and cheap) manufacturer of reliable slip rings rated for 240VAC (we'll be in...
Reliable AND Cheap? I think you need to pick just one of those. From my experience pro slip rings are expensive. Some people I know make their own with...
Hi, i have a introboard and everything worked fine until I started with the photocell sensor. I get nothing out from that, not with my own small flash program...
Hi Magnus - does that mean that you've tried other sensors on the analog in terminal and they've worked ok? Can you confirm that you have the red wire to 5V,...
I don't have much electronics here att home so the only two sensors I've tried with is the two photocell sensors. I tried connecting the intro pushbutton...
I'm, sorry all. I used: var ain0:TAin = new TAin(0); instead of: var ain:TIntroAin = new TIntroAin( 0 ); so now it works perfect =) /magnus ... sensors ... the...
_* *_ Below is some information about a summer teaching position at the Chabot Space & Science Center in Oakland, CA. If you have questions or would like more...
A while back, we purchased 2 of Makingthings' 57BYG step motors (SKU ACC-STP-57BYG, 12v) for another project - used with the stepper motor controller. We no...
Hi Lee - unfortunately, it's not possible to drive a stepper motor from either the dual 2A motor controller or the servo controller boards. The only Teleo...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
