Hi Steve - sounds like you may have gotten a sensor that is not wired up correctly. I would definitely not hook the sensor up again until it's either repaired...
Replaced the sensor and it works fine. Thanks. Onto the bigger challenge: I'm trying to read temperature changes in tenths or hundredths of a degree, but a...
Hi all, I need to track some movements on a stage, I read that you need a NTSC camera to use with the videomodule, could I use PAL cameras? Am I correct if I...
Apologies for cross posting MA in Digital Performance School of Arts Brunel University West London Course Convener: Paul Verity Smith This is a distinctive and...
Hi, I'm building a new project here, and I am in need of locating a decent (and cheap) manufacturer of reliable slip rings rated for 240VAC (we'll be in...
Reliable AND Cheap? I think you need to pick just one of those. From my experience pro slip rings are expensive. Some people I know make their own with...
Hi, i have a introboard and everything worked fine until I started with the photocell sensor. I get nothing out from that, not with my own small flash program...
Hi Magnus - does that mean that you've tried other sensors on the analog in terminal and they've worked ok? Can you confirm that you have the red wire to 5V,...
I don't have much electronics here att home so the only two sensors I've tried with is the two photocell sensors. I tried connecting the intro pushbutton...
I'm, sorry all. I used: var ain0:TAin = new TAin(0); instead of: var ain:TIntroAin = new TIntroAin( 0 ); so now it works perfect =) /magnus ... sensors ... the...
_* *_ Below is some information about a summer teaching position at the Chabot Space & Science Center in Oakland, CA. If you have questions or would like more...
A while back, we purchased 2 of Makingthings' 57BYG step motors (SKU ACC-STP-57BYG, 12v) for another project - used with the stepper motor controller. We no...
Hi Lee - unfortunately, it's not possible to drive a stepper motor from either the dual 2A motor controller or the servo controller boards. The only Teleo...
Hey Barney - not directly as is, but if you filter the pwm signal from the rapidly switching signal that it is to a continuous voltage, you certainly could. ...
A resistor and a capacitor. RC to be much greater than the period of the PWM. R to be much less than the input resistance of the stepper block. Assume the PWM...
Don Day
don@...
Feb 27, 2006 11:05 pm
1130
I think a simple capacitor, or at most a capacitor plus resistor should be sufficient filtering....
Thanks for all the input and ideas! had thought about the PWM but didn't think it would quite work the way we'd expect. we're going to 'trade' those motors to...
... Well ok perhaps an explanation is needed. I am using the telio board in a lighting project and i need to mimic the behavior of an led array in real life. I...
The AC Switch block uses a silicon relay to switch its load on and off. This device uses an LED internally to optically connect the low voltage side from the...
Thanks alot that saves my life. I'm connecting to 12V halogens and i thought i may need relays in between to help with the current levels. K ... and so ... ...
Will the AC switch block work for very low voltage AC, like 12V? I know the AC dimmer block is only designed for line voltage AC, 120-240V....
Don Day
don@...
Mar 14, 2006 7:53 pm
1137
hello everyone, i'm preparing one work which im planning buy teleo module for it's simple use with Max.i need 7(maybe 10) stepper motors installed on domestic...
Don is certainly right. The AC Switches are intended for AC line voltages. To switch DC 12V you might want to look into some Logic Level MOSFETS. D....
hiya, i am trying to control a stepper motor using the teleo stepper block and intro module. from what i've read on a few of the previous threads, i gather...
Hi- I just tried to get my Teleo system to work on my MacBook Pro. Under Max 4.5.7. There error I get in the Max window is: New t.mio.ain object, version 1.1 ...
I thought this might interest some of you. Apologies for cross postings. mz -=-=-=-=- 2006 Summer Workshops at CNMAT Jitter Night School, July 21-23, 7-10 PM ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
