We're getting a startup delay on initially running a Flash8 SWF that uses the TIntroAIN and TAIN. Currently we have a sequence of Flash movies that load one...
New Product Development Consultant / Product Scout / Licensing Agent relocating to the Northwest back-country? I am new to the site. I am conducting an...
hi, i'm new here. i purchased the intro module and the 2A motor controller. how can i have an output of 30v. as i understood the motor controller could go over...
I saw in the flash class user guide that it is possible to use the system with the XML server running on one machine and the Flash application running on...
Can you first confirm that you can telnet into the desired machine on port 50000? If this fails, confirm that you have no firewall settings or other network...
Well, first of all, both machines are Macs running OS X. I turned the firewall off on the host machine and this seemed to allow me to telnet into it on port...
I seemed to have figured this out (least for trying over my local area network, but the principles seem the same): 1. Teleo XML server on same machine as web...
Hi Folks, I'm just beginning to work with a few modules and flash. It seems to work nicely but I've encountered a problem - I don't know how to shut the teleo...
hi, i'm wondering if it might be possible to control a basic stamp from the teleo multi io. i'm using a parallax bs2 to control servos. thanks, david...
You could use the PWM out through a low pass filter (resistor in series and capacitor connected to ground) to create a voltage, which you then read with the...
NASA has recently answered with a world press release to the prediction of a mega tsunami, created by a possible impact of a fragment of the comet SW-3 on MAY...
Nice paranoid spam. SW3 is a real broken-up comet, is nearby A satellite called Contour plans to look at the chunk edges. anyway, since M-T is on the other...
One thing to note, the gregorian calendar May 25th correlates to May 12 in the Julien calendar. This just makes one wonder what else might me less than...
... That you read far enough to spot the error, and that you answered in such a logical and reasonable manner tells me you took his email far more seriously...
The user who sent this email has been removed from this list. MakingThings has a very low tolerance for spammers of any sort on this mailinglist. We continue...
Hi, I am working on making a device using my teleo, to draw on a Magna Doodle (you know those drawing tablet toys for kids). As it uses a magnet to create...
Hi Darcy, You could do this in a couple of ways. You could experiment with a couple of different electromagnet configurations. Perhaps winding a coil around...
Thanks for the reply, Yes I have had a good look at the wire+nail trick. But the device will require multiple electromagnets so I really was wondering about a...
Hello, I am using two mio modules in a setup. Because of this I have to set the address of each of these in order for my sensors to know which module to speak...
John Thompson
leroybanana@...
May 21, 2006 5:42 pm
1175
I work on a MacBookPro with OSX 10.4.6 and latest MAX and Jitter. I get the Teleo freeze after a while (5 minutes) when I use two relays (module dout) to...
Hi John - so, the procedure should be as follows: 1. Press the pushbutton on the module whose address you'd like to change until the LED is blinking rapidly. ...
Hi Andreas, My first thought was voltage drop when you switch on the relays, but you say it happens when you use LEDs instead so that's probably not the...
Hi Andreas - it sounds very much like the lights are most suspcious here. Firstly, it's fine not to have the FTDI ReEnumerate file in StartupItems, and the...
Thanks for the fast reply. To the Intro follows a Multi, Digital and an Analogue module for sensors. I bought boards or lamps (readymades) with leds on it to...
Hi Andreas, Without doing all the math, here's the quick rule of thumb: If it works fine with two LEDs, but fails with the larger number of LEDs or other lamps...
Hello Michael, I added a other 3.8 A for the devices of the Dout Module. If I turn on one relay on fast switching position (665m), it freezes quickly again....
Hi, first time posting, I'm dealing with power pwm interfacing for neons. Not to confuse, I assume my neons behave the same way as regular loads of 400mA each...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
