Tried to do it on my own, <sob> I need help! <smile> Using a full license (legal) Flash MX 2004. Plus 'iSwiff' and 'Gordon' as backups. (Mac Software) 1)...
Ah hah...looks like you're trying to use the Teleo Flash files with the Make Controller Kit. This won't work. Not sure if you're also using the Teleo XML...
Yeap! Those be the files that are giving me the error! (http://www.makingthings.com/makecontrollerkit/guides/adobe_flash.htm) Downloaded them again, same...
i am unfortunately heartened by this - i'm still having the same problems with the flash examples files - unable to open them up! thought i was a loner with...
Speaking of connectors...I was wondering if anyone knows of a trick to connect 2 wires to the little connector tabs on one of the Force Sensor Resistors. I am...
Connect one short length of wire to the sensor, then connect the two wires to that. You can twist them together, etc. Much easier. _____ From: brent...
hi, I have one Servo Module of Teleo with 6 servo (15 kg) ones working. Accustom gives the following error me: The USB Serial Port has been unpluggedwhile an...
That certainly is possible. The quickest solution is probably just to replace the power supply you're using with a more powerful one - do you have an idea of...
just so i'm clear... I can connect the ONE short wire to BOTH of the little tabs on the FSR. Then I twist the TWO wires onto the ONE short wire (to the end...
Nope. I thought you wanted to connect two wires to one terminal of the FSR. You definitely need one separate wire for each terminal of the FSR. D. _____ From:...
Okay. that's what I thought. I'm just not that good at making a solder connection that doesn't ooze over and touch the other little tab. It can be very...
is it possible to use this srf08 ultrasonic sensor with the NEW makecontroller? http://www.warburtech.com/sensors/srf08.ultrasonic.rangefinder if yes, in which...
Sent an email directly to Making Things, they suggested I use Yahoo Group to help with the matter... (Which I did).. Learned that MANY people are having this...
Hi David - I sent an email back out on the group that this was most likely due to the fact that the files were Flash 8 files, so not compatible with Flash MX...
i'm trying to test the analogin example for max, and in max i keep receiving the error: error:udp.recv: bind to port 10000 unsuccessful. there is probably...
Hi, You may remember I asked sometime back if it would be ok to use 3.5mm stereo minijacks as connectors sensor connectors into a teleo. This seems to work ...
Hi Jim - it's no problem at all to switch these in and out while the board is powered, but of course if you actually switch them around you could do some...
Now that OSC over USB is working, is it possible to change the network settings for heavy mode via OSC? I looked in the OSC reference, but I was unable to find...
Hi Josh - this is indeed possible. Just send it the same message as you would over the Ethernet, but obviously from the USB command line in mchelper, and not...
Liam, Thanks for the reply. One problem though... The OSC reference on the makingthings site does not reference any /network subsytem. Is there a different...
The most complete OSC reference is up at http://www.makingthings.com/ makecontrollerkit/software/doc/html/group___o_s_c.html It's a little mysterious how to...
Where can I get a copy of the working Flash MX files (URL)? Tried another download of MakeFlashSamples.zip off the site, get the same error (though it was only...
Liam, Thanks again for the rapid response. I was able to use OSC to get my network settings fixed up. Let me just start by saying that I am having a blast...
Thanks for the reply. I'm not sure if I explained things very well. What I'm concerned about is the moment where a minijack is inserted into the socket. Is ...
Hi group - Anyone have an experiences or attempts at using an inductive proximity sensor with a telio? I don't even know if its possible. I'm just shopping...
