hi MT, i just installed the latest Max version - version 4.6.2 - on my macBook - 2GHz Mac OS X 10.4.8 - and can't get my teleo's working. I get the error...
Hi there folks, I ordered another Teleo Starter kit some time ago and got a receipt from makingThings on the 6th of October but nothing since. I have been ...
Hello, I have a question about the limits of the servo block when used with the Teleo intro module. I would like to use a servo that will draw 4200mA when...
The Servo Block has a separate input for power if you want to go over the approximately 1A available on board. Supply it with 4V - 6V at the current you need...
hmmmm... So if i don't use the SV terminal and I stall the servo bad things are going to happen right? And I would need something like the following for the SV...
Anybody there who has an answer on this question please? Do I still need to run max/msp in Rosetta-mode or are the provided teleo-intel-externals fully...
The Teleo externals are still currently PPC only, but we hope the Universal versions will be ready by the end of the year. Thanks Don! We'll certainly make...
Hello, I have I modulate with 6 servo (HS -705MG) connected. A transformer gives 12 V and 3.5 A. The question is that all the servo ones have been burned me...
Teleo Servo Module or Make Controller? In both cases there are on-board regulators / dc -dc converters to create 5V or 6V. Are you saying you think the servo's...
... Servo Module ... The system has been 1 month perfectly working. a day was an electrical power failure in the building. After reinitiating the system the...
hi, I have verified that single has burned one of the servo ones, but the peculiar thing is that all connected did not work any. 1 - The servo module it blocks...
If one servo was drawing a lot of current, it might shut the power supply down or reduce its voltage to the point the other servos don't wrok. 12 hours is fine...
I am going to put a switch digital (Motorola Semiconducting MC14066B) so that at the servo ones voltage arrives to them when they are going away to activate....
The 4066 will work fine for switching the control signal to the servo, but its resistance will be way too high for switching the power (+_4.8V to 6.0V) to the...
Don Day
don@...
Nov 22, 2006 6:25 pm
1450
Sorry my ignorance but I do not understand very well, I am not electronic. that you recommend to me and as I connect it? thaks in advance ... servo. ... Behalf...
Currently, the Teleo Max externals are not built as Universal Binaries which means they will not run on Intel based Macs. Running Max 4.5 is your best bet if...
Hi. I'm trying to build a linear positioning system using the Make Controller to control a motor that will drive a horizontal pulley system. I think the best...
i'm experimenting with basic circuits and there's something i'm having a hard time understanding. i feel like i'm grasping the concept of voltage dividers,...
Hi there - with regards to the voltage divider, it doesn't matter whether you have the device or the resistor on either side, the important part is the...
right now i just want to know if the resistors that come in the assemblies for the bend and photo sensors are the same (still 1k for the photo and 12k for the...
Spending my holiday break once again attempting to get my controller to do something. Anything. Installed the Extensions into the Extensions Manager. Rewrote...
(Using Mac OS X 10.4.8 and Flash MX Pro 7.0) Got the XML Server running, I have Heavy running, I can HTTP into the controller and get the state of the ports....
The Flosc library is trying to load the Delegate class - this is a class that was introduced in Flash MX 2004 7.2. Do you have the option to upgrade your...
OH HAPPY DAYS! It works! Upgrading to Flash MX 2004 7.2 from 7.0 fixed it. <smile> Now why didn't someone mention that sooner? - Had an issue with upgrading...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
